6-Speed Direct Shift Gearbox (DSG/02E) - Revision history

Dana at 14:23, 7 October 2025

2025-10-07T14:23:38Z

← Older revision		Revision as of 14:23, 7 October 2025
Line 134:		Line 134:
	* Complete [[6-Speed Direct Shift Gearbox (DSG/02E)#Basic Setting \| Basic Settings]]		* Complete [[6-Speed Direct Shift Gearbox (DSG/02E)#Basic Setting \| Basic Settings]]
	* Complete the [[6-Speed Direct Shift Gearbox (DSG/02E)#Special Procedures \| Defined Test Drive]]		* Complete the [[6-Speed Direct Shift Gearbox (DSG/02E)#Special Procedures \| Defined Test Drive]]

			== Special Notes ==
			* Some users may find the chart and Transmission Digest links in post #6 of this thread helpful: https://forums.ross-tech.com/index.php?threads/50808/#post-416443

	[[Category:Transmissions]]		[[Category:Transmissions]]

Andy: /* Basic Setting */

2019-05-07T12:52:41Z

Basic Setting

← Older revision		Revision as of 12:52, 7 May 2019
Line 17:		Line 17:
	* Engine ON (Idling) for one minute or more		* Engine ON (Idling) for one minute or more
	* Brake Pedal operated (hold for the whole procedure)		* Brake Pedal operated (hold for the whole procedure)
	* Throttle Pedal not operated<br>		* Throttle Pedal not operated
			* Cruise control is switched OFF<br>

	'''''NOTE:''' Be sure to perform the following steps in the sequence shown, followed by the defined test drive.''		'''''NOTE:''' Be sure to perform the following steps in the sequence shown, followed by the defined test drive.''

Peter: /* Basic Setting */

2017-06-14T13:55:26Z

Basic Setting

← Older revision		Revision as of 13:55, 14 June 2017
Line 12:		Line 12:
	== Basic Setting ==		== Basic Setting ==
	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019.		* Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group 019. (Fluid Level needs to be correct!)
	* Selector Lever in P		* Selector Lever in P
	* Ignition ON		* Ignition ON
Line 99:		Line 99:
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>
	Perform the Defined Test Drive.<br><br>		Perform the Defined Test Drive.<br><br>


	== Special Procedures ==		== Special Procedures ==

Dana at 16:47, 19 December 2016

2016-12-19T16:47:48Z

← Older revision		Revision as of 16:47, 19 December 2016
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__

	'''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Direct-Shift_Gearbox Wikipedia entry]. Additional information can be found in the [[Official Factory Repair Information]] and sources such as [http://www.bentleypublishers.com//volkswagen/technical-training/vw-02e-direct-shift-gearbox-ssp.html Bentley Publisher's SSP (Self-Study Program)] .<br>		'''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Direct-Shift_Gearbox Wikipedia entry]. Additional information can be found in the [[Official Factory Repair Information]] and sources such as [http://www.bentleypublishers.com//volkswagen/technical-training/vw-02e-direct-shift-gearbox-ssp.html Bentley Publisher's VW SSP (Self-Study Program 851403)] and [http://www.bentleypublishers.com//audi/technical-training/audi-02e-direct-shift-gearbox-ssp.html Bentley Publisher's Audi SSP (Self-Study Program 951403)].<br>
	<br>		<br>

Dana: /* Replacement */

2016-12-19T16:44:03Z

Replacement

← Older revision		Revision as of 16:44, 19 December 2016
Line 129:		Line 129:

	== Replacement ==		== Replacement ==
			Replacement Mechatronic units should be ordered by VIN based on [[Production Codes (PR-Codes) can be found on the Vehicle Data Label \| PR Codes]] to confirm vehicle compatibility.
	* Run and save a complete Auto-Scan and save it prior to Mechatronic unit removal. See the [http://www.ross-tech.com/vcds/tour/autoscan.html Online Manual Auto-Scan].<br>		* Run and save a complete Auto-Scan and save it prior to Mechatronic unit removal. See the [http://www.ross-tech.com/vcds/tour/autoscan.html Online Manual Auto-Scan].<br>
	* Enter the original [[6-Speed Direct Shift Gearbox (DSG/02E)#Coding \| Coding]] into the New Coding section of the replacement controller.		* Enter the original [[6-Speed Direct Shift Gearbox (DSG/02E)#Coding \| Coding]] into the New Coding section of the replacement controller.

Dana at 19:05, 22 July 2016

2016-07-22T19:05:55Z

← Older revision		Revision as of 19:05, 22 July 2016
Line 56:		Line 56:
	** Basic Settings group 062 may take several minutes to complete. The final values may report: [18 \| 18 \| .285 \| .24] and Basic Settings will report ON when finished.		** Basic Settings group 062 may take several minutes to complete. The final values may report: [18 \| 18 \| .285 \| .24] and Basic Settings will report ON when finished.
	** If Basic Settings group 062 reports ''ERROR:\| Group 062\| Not \| Available'' try test driving the vehicle and repeating at normal operating temp.		** If Basic Settings group 062 reports ''ERROR:\| Group 062\| Not \| Available'' try test driving the vehicle and repeating at normal operating temp.
	''Internal Ref: ST?ID=66725 and ''		''Internal Ref: ST?ID=66725 and E?ID=309867''

	'''''Control Module Software Version >= 0800 :'''''		'''''Control Module Software Version >= 0800 :'''''

Dana at 19:00, 22 July 2016

2016-07-22T19:00:40Z

← Older revision		Revision as of 19:00, 22 July 2016
Line 52:		Line 52:
	'''[ON/OFF/Next]'''<br>		'''[ON/OFF/Next]'''<br>

	Special ~~note:~~ When found in the early software level (0627) (8N) Audi TT Basic Settings group 062 may take several minutes to complete. The final values may report: [18 \| 18 \| .285 \| .24] and Basic Settings will report ON when finished.		Special notes.
			*When found in the early software level (0627/0628) (8N) Audi TT:
	''Internal Ref: ST?ID=66725''		** Basic Settings group 062 may take several minutes to complete. The final values may report: [18 \| 18 \| .285 \| .24] and Basic Settings will report ON when finished.
			** If Basic Settings group 062 reports ''ERROR:\| Group 062\| Not \| Available'' try test driving the vehicle and repeating at normal operating temp.
			''Internal Ref: ST?ID=66725 and ''

	'''''Control Module Software Version >= 0800 :'''''		'''''Control Module Software Version >= 0800 :'''''

Dana: /* Clutch Adaptation */

2016-04-04T20:45:05Z

Clutch Adaptation

← Older revision		Revision as of 20:45, 4 April 2016
Line 51:		Line 51:
	Activate the Basic Setting.<br>		Activate the Basic Setting.<br>
	'''[ON/OFF/Next]'''<br>		'''[ON/OFF/Next]'''<br>

			Special note: When found in the early software level (0627) (8N) Audi TT Basic Settings group 062 may take several minutes to complete. The final values may report: [18 \| 18 \| .285 \| .24] and Basic Settings will report ON when finished.

			''Internal Ref: ST?ID=66725''

	'''''Control Module Software Version >= 0800 :'''''		'''''Control Module Software Version >= 0800 :'''''

Dana at 15:00, 12 December 2014

2014-12-12T15:00:17Z

@@ Line 3: / Line 3: @@
 '''General Information''' about this Transmission can be found in the [http://en.wikipedia.org/wiki/Direct-Shift_Gearbox Wikipedia entry].  Additional information can be found in the [[Official Factory Repair Information]] and sources such as [http://www.bentleypublishers.com//volkswagen/technical-training/vw-02e-direct-shift-gearbox-ssp.html Bentley Publisher's SSP (Self-Study Program)] .<br>
 <br>
 == Basic Setting ==
 '''<u>Prerequisites:</u>'''<br>
@@ Line 112: / Line 119: @@
 * Customers with TDI's have reported that an RPM range of 2000-2500 rpm is sufficient.
 [[Category:Transmissions]]

Dana at 18:30, 16 April 2013

2013-04-16T18:30:14Z

← Older revision		Revision as of 18:30, 16 April 2013
Line 22:		Line 22:
	Group 061<br>		Group 061<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	* When you go to Basic Settings 061 and click GO the screen may look like this: [http://~~img404~~.~~imageshack~~.us/~~img404~~/~~5604~~/~~061go~~.png Basic Settings 061]<br>		* When you go to Basic Settings 061 and click GO the screen may look like this: [http://wiki.ross-tech.com/wiki/images/3/35/02-04-061_start.png Basic Settings 061]<br>
	* Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to '''On''' when finished: [http://~~img38~~.~~imageshack~~.us/~~img38~~/~~5521~~/~~061done~~.png Basic Settings 061]<br>		* Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to '''On''' when finished: [http://wiki.ross-tech.com/wiki/images/1/1e/02-04-061_end.png Basic Settings 061]<br>

	Wait until Basic Settings has switched to ON and all numbers have stopped moving. This may take one minute.<br>		Wait until Basic Settings has switched to ON and all numbers have stopped moving. This may take one minute.<br>
Line 31:		Line 31:
	Group 060<br>		Group 060<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	* When you go to Basic Settings 060 and click GO the screen may look like this: [http://~~img227~~.~~imageshack~~.us/~~img227~~/~~5338~~/~~060go~~.png Basic Settings 060]<br>		* When you go to Basic Settings 060 and click GO the screen may look like this: [http://wiki.ross-tech.com/wiki/images/a/a8/02-04-060_start.png Basic Settings 060]<br>
	* Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to '''On''' when finished: [http://~~img695~~.~~imageshack~~.us/~~img695~~/~~5637~~/~~060done~~.png Basic Settings 060]<br>		* Wait until the numbers quit moving and the trans will quit making noises. Basic Settings switches to '''On''' when finished: [http://wiki.ross-tech.com/wiki/images/3/3e/02-04-060_end.png Basic Settings 060]<br>

	Wait until Basic Settings has switched to ON and all numbers have stopped moving.		Wait until Basic Settings has switched to ON and all numbers have stopped moving.