Audi A4 (8K) Airbag Audi 10 - Revision history

Dana at 21:51, 22 January 2021

2021-01-22T21:51:30Z

← Older revision		Revision as of 21:51, 22 January 2021
Line 19:		Line 19:
	=== Seat Occupied Recognition Control Module (J706) ===		=== Seat Occupied Recognition Control Module (J706) ===

	If the Seat Occupied Recognition Control Module (J706) or the seat itself have been replaced, the reset has to be performed.		If the Seat Occupied Recognition Control Module (J706) or the seat itself have been replaced, the reset has to be performed.<br>
	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* The vehicle is between 5° and 35°C (40° ~ 95°F).		* The vehicle is between 5° and 35°C (40° ~ 95°F).
Line 38:		Line 38:
	'''[Stop]'''<br>		'''[Stop]'''<br>

	The Seat occupied recognition serial number reset has been performed. Proceed directly to the [[A4 (8K) Airbag Audi 10#Seat Occupied Recognition Control Module (J706): Reset \| Seat Occupied Recognition Control Module (J706): Reset]]		The Seat occupied recognition serial number reset has been performed. Proceed directly to the [[Audi A4 (8K) Airbag Audi 10#Seat Occupied Recognition Control Module (J706): Reset \| Seat Occupied Recognition Control Module (J706): Reset]]

	=== Seat Occupied Recognition Control Module (J706): Reset ===		=== Seat Occupied Recognition Control Module (J706): Reset ===

Dana at 14:06, 21 October 2016

2016-10-21T14:06:08Z

← Older revision		Revision as of 14:06, 21 October 2016
Line 66:		Line 66:

	== Replacement ==		== Replacement ==
	Replacement of the Airbag control module may result in Component Protection (CP) DTCs such as U1101 and U1100. Component Protection can only be learned/disabled using the Factory Tool in Combination with an online Connection with GeKo access.		Replacement of the Airbag control module may result in Component Protection (CP) DTCs such as [[U1101]] and [[U1100]]. Component Protection can only be learned/disabled using the Factory Tool in Combination with an online Connection with GeKo access.

	The Coding and Parameterization steps are performed online as well, but those steps use a process called SVM (Software Version Management). SVM is a system used by VW/Audi to flash update control modules, and in certain cases, to change their Coding, Adaptation and configure Parameters.		The Coding and Parameterization steps are performed online as well, but those steps use a process called SVM (Software Version Management). SVM is a system used by VW/Audi to flash update control modules, and in certain cases, to change their Coding, Adaptation and configure Parameters.

	Even if you have a complete Auto-Scan saved prior to replacing the Airbag module and the replacement part number is EXACTLY the same we strongly recommend using SVM to code and unlock CP for liability reasons.		Even if you have a complete Auto-Scan saved prior to replacing the Airbag module and the replacement part number is EXACTLY the same we strongly recommend using SVM to code and unlock CP for liability reasons.

Dana: /* Seat Occupied Recognition Control Module (J706): Reset */

2016-10-21T13:42:41Z

Seat Occupied Recognition Control Module (J706): Reset

← Older revision		Revision as of 13:42, 21 October 2016
Line 62:		Line 62:

	The seat occupied recognition reset reset has been performed. Fault codes should clear after an ignition cycle.		The seat occupied recognition reset reset has been performed. Fault codes should clear after an ignition cycle.

			'''Note''' If you get a "Request Sequence Error" when performing the above procedures, try '''[Coding - 07]''' the '''[15 - Airbags]''' module with the same Coding value it already has. It may give you an error but proceed anyway with the two Output Tests steps shown above.

	== Replacement ==		== Replacement ==

Dana at 16:38, 12 October 2016

2016-10-12T16:38:19Z

← Older revision		Revision as of 16:38, 12 October 2016
Line 64:		Line 64:

	== Replacement ==		== Replacement ==

	Replacement of the Airbag control module may result in Component Protection (CP) DTCs such as [[U1101]] and [[U1100]]. Component Protection can only be learned/disabled using the Factory Tool in Combination with an online Connection using a process called SVM (Software Version Management). SVM is a system used by VW/Audi to flash update control modules, and in certain cases, to change their Coding, Adaptation and unlock Component Protection.

	Even if you have a complete Auto-Scan saved prior to replacing the Airbag module and the replacement part number is EXACTLY the same we strongly recommend using SVM to code and unlock CP for liability reasons.

	--

	~~'''Revised replacement notes:'''~~

	Replacement of the Airbag control module may result in Component Protection (CP) DTCs such as U1101 and U1100. Component Protection can only be learned/disabled using the Factory Tool in Combination with an online Connection with GeKo access.		Replacement of the Airbag control module may result in Component Protection (CP) DTCs such as U1101 and U1100. Component Protection can only be learned/disabled using the Factory Tool in Combination with an online Connection with GeKo access.

Dana: /* Replacement */

2016-10-12T16:07:35Z

Replacement

← Older revision		Revision as of 16:07, 12 October 2016
Line 66:		Line 66:

	Replacement of the Airbag control module may result in Component Protection (CP) DTCs such as [[U1101]] and [[U1100]]. Component Protection can only be learned/disabled using the Factory Tool in Combination with an online Connection using a process called SVM (Software Version Management). SVM is a system used by VW/Audi to flash update control modules, and in certain cases, to change their Coding, Adaptation and unlock Component Protection.		Replacement of the Airbag control module may result in Component Protection (CP) DTCs such as [[U1101]] and [[U1100]]. Component Protection can only be learned/disabled using the Factory Tool in Combination with an online Connection using a process called SVM (Software Version Management). SVM is a system used by VW/Audi to flash update control modules, and in certain cases, to change their Coding, Adaptation and unlock Component Protection.

			Even if you have a complete Auto-Scan saved prior to replacing the Airbag module and the replacement part number is EXACTLY the same we strongly recommend using SVM to code and unlock CP for liability reasons.

			--

			'''Revised replacement notes:'''

			Replacement of the Airbag control module may result in Component Protection (CP) DTCs such as U1101 and U1100. Component Protection can only be learned/disabled using the Factory Tool in Combination with an online Connection with GeKo access.

			The Coding and Parameterization steps are performed online as well, but those steps use a process called SVM (Software Version Management). SVM is a system used by VW/Audi to flash update control modules, and in certain cases, to change their Coding, Adaptation and configure Parameters.

	Even if you have a complete Auto-Scan saved prior to replacing the Airbag module and the replacement part number is EXACTLY the same we strongly recommend using SVM to code and unlock CP for liability reasons.		Even if you have a complete Auto-Scan saved prior to replacing the Airbag module and the replacement part number is EXACTLY the same we strongly recommend using SVM to code and unlock CP for liability reasons.

Dana at 21:34, 16 March 2016

2016-03-16T21:34:08Z

← Older revision		Revision as of 21:34, 16 March 2016
Line 30:		Line 30:
	'''[15 - Airbags]'''<br>		'''[15 - Airbags]'''<br>
	'''[Security Access - 16]'''<br>		'''[Security Access - 16]'''<br>
	Enter the code shown in the pop-up balloon ~~to enable the basic setting~~.<br>		Enter the code shown in the pop-up balloon.<br>
	'''[Do it!]'''<br>		'''[Do it!]'''<br>
	'''[Output Tests-03]'''<br>		'''[Output Tests-03]'''<br>
Line 53:		Line 53:
	'''[15 - Airbags]'''<br>		'''[15 - Airbags]'''<br>
	'''[Security Access - 16]'''<br>		'''[Security Access - 16]'''<br>
	Enter the code shown in the pop-up balloon ~~to enable the basic setting~~.<br>		Enter the code shown in the pop-up balloon.<br>
	'''[Do it!]'''<br>		'''[Do it!]'''<br>
	'''[Output Tests-03]'''<br>		'''[Output Tests-03]'''<br>

Dana at 17:49, 26 February 2015

2015-02-26T17:49:21Z

@@ Line 9: / Line 9: @@
     ROD: EV_AirbaECUVWAUDI010_AU48.rod
-== Coding ==
+== Adaptation ==
-Replacement of the Airbag control module may result in Component Protection (CP)  DTCs such as [[U1101]] and [[U1100]]. Component Protection can only be learned/disabled using the Factory Tool in Combination with an online Connection using a process called SVM (Software Version Management).  SVM is a system used by VW/Audi to flash update control modules, and in certain cases, to change their Coding, Adaptation and unlock Component Protection.
+Used to deactivate individual airbag components (see repair manual for details).
 == Security Access ==
 * Will appear in a pop-up balloon when connected to this controller with VCDS.
-== Basic Setting ==
+== Special Procedures ==

RtWiKiSyS0p at 17:20, 26 February 2015

2015-02-26T17:20:44Z

← Older revision		Revision as of 17:20, 26 February 2015
Line 3:		Line 3:
	The Airbag Audi 10 system can be identified by evaluating the '''AirbagVW-AU10''' Component data in the Auto-Scan:		The Airbag Audi 10 system can be identified by evaluating the '''AirbagVW-AU10''' Component data in the Auto-Scan:

	Address 15: Airbags (J234) ~~Labels: 8K0-959-655.clb~~		Address 15: Airbags (J234)
	Part No SW: 8K0 959 655 K HW: 8K0 959 655 K		Part No SW: 8K0 959 655 K HW: 8K0 959 655 K
	Component: '''AirbagVW-AU10''' H45 0610		Component: '''AirbagVW-AU10''' H45 0610

Dana: Created page with "FORCETOC The Airbag Audi 10 system can be identified by evaluating the '''AirbagVW-AU10''' Component data in the Auto-Scan: Address 15: Airbags (J234) Labels: 8K..."

2015-02-26T17:11:10Z

Created page with "__FORCETOC__ The Airbag Audi 10 system can be identified by evaluating the '''AirbagVW-AU10''' Component data in the Auto-Scan: Address 15: Airbags (J234) Labels: 8K..."

New page

__FORCETOC__

The Airbag Audi 10 system can be identified by evaluating the '''AirbagVW-AU10''' Component data in the Auto-Scan:

Address 15: Airbags (J234) Labels: 8K0-959-655.clb
Part No SW: 8K0 959 655 K HW: 8K0 959 655 K
Component: '''AirbagVW-AU10''' H45 0610
ASAM Dataset: EV_AirbaECUVWAUDI010 003010
ROD: EV_AirbaECUVWAUDI010_AU48.rod

== Coding ==

Replacement of the Airbag control module may result in Component Protection (CP) DTCs such as [[U1101]] and [[U1100]]. Component Protection can only be learned/disabled using the Factory Tool in Combination with an online Connection using a process called SVM (Software Version Management). SVM is a system used by VW/Audi to flash update control modules, and in certain cases, to change their Coding, Adaptation and unlock Component Protection.

Even if you have a complete Auto-Scan saved prior to replacing the Airbag module and the replacement part number is EXACTLY the same we strongly recommend using SVM to code and unlock CP for liability reasons.

== Security Access ==
* Will appear in a pop-up balloon when connected to this controller with VCDS.

== Basic Setting ==