https://wiki.ross-tech.com/wiki/index.php?action=history&feed=atom&title=Audi_R8_%2842%29_Brake_Electronics 2026-04-22T07:04:17Z Revision history for this page on the wiki MediaWiki 1.43.3 https://wiki.ross-tech.com/wiki/index.php?title=Audi_R8_(42)_Brake_Electronics&diff=8068&oldid=prev 2016-06-09T14:54:28Z

<p>Created page with &quot;__FORCETOC__ == Coding == Most repair manual sources do not cover this Bosch 8.0 ABS system. When the module is replaced with new it is advised to use the original coding va...&quot;</p> <p><b>New page</b></p><div>__FORCETOC__<br /> == Coding ==<br /> <br /> Most repair manual sources do not cover this Bosch 8.0 ABS system. When the module is replaced with new it is advised to use the original coding value from the old unit. If this is not possible, registered users can [http://www.ross-tech.com/contact.html contact us directly] with a complete [http://www.ross-tech.com/vcds/tour/autoscan.html Auto Scan] and VIN number.<br /> <br /> <br /> == Basic Setting ==<br /> <br /> === Steering Angle Sensor (G85) Calibration ===<br /> <br /> &#039;&#039;&#039;[Select]&#039;&#039;&#039;&lt;br&gt;<br /> &#039;&#039;&#039;[03 - ABS Brakes]&#039;&#039;&#039;&lt;br&gt;<br /> <br /> Turn steering wheel at least 30 ° left and back straight ahead.&lt;br&gt;<br /> <br /> &#039;&#039;&#039;[Security Access - 16]&#039;&#039;&#039;&lt;br&gt;<br /> Enter 40168&lt;br&gt;<br /> &#039;&#039;&#039;[Do It!]&#039;&#039;&#039;&lt;br&gt;<br /> <br /> &#039;&#039;&#039;[Basic Settings - 04]&#039;&#039;&#039;&lt;br&gt;<br /> Group 001&lt;br&gt;<br /> &#039;&#039;&#039;[Go!]&#039;&#039;&#039;&lt;br&gt;<br /> Activate the Basic Setting.&lt;br&gt;<br /> &#039;&#039;&#039;[ON/OFF/Next]&#039;&#039;&#039;&lt;br&gt;<br /> After a successful basic setting, field 3 should say &quot;OK&quot;.&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> <br /> &#039;&#039;&#039;[Fault Codes - 02]&#039;&#039;&#039;&lt;br&gt;<br /> All fault codes should have disappeared.&lt;br&gt;<br /> &#039;&#039;&#039;[Done, Go Back]&#039;&#039;&#039;&lt;br&gt;<br /> <br /> &#039;&#039;&#039;[Close Controller, Go Back - 06]&#039;&#039;&#039;&lt;br&gt;<br /> <br /> ==== Special Note ==== <br /> <br /> * After doing the G85 Calibration, you may get a 01486 - System Function Test Active, this is normal. Please see [[01486]].<br /> <br /> <br /> == Replacement ==<br /> <br /> * First, Code the module with the original coding value from the old unit. No Login or Security Access is needed.<br /> * Next, perform the G85 Calibration.<br /> * Make sure that no faults are present and that the ABS and ESP lamps are off when you exit out of the controller.</div>

Dana