Bentley Continental (3W) Tire Pressure Monitoring - Revision history

Dana: /* Initialization */

2017-09-28T17:05:19Z

Initialization

← Older revision		Revision as of 17:05, 28 September 2017
Line 18:		Line 18:
	Adaptation Channel '''001'''<br>		Adaptation Channel '''001'''<br>
	'''[Read]'''<br>		'''[Read]'''<br>
	Enter '''0''' as new Value.<br>		Enter '''1''' as new Value.<br>
	'''[Test]'''<br>		'''[Test]'''<br>
	'''[Save]'''<br>		'''[Save]'''<br>

Andy at 13:00, 22 March 2016

2016-03-22T13:00:35Z

← Older revision		Revision as of 13:00, 22 March 2016
Line 36:		Line 36:
	* Now drive the vehicle until all Wheel Pressure Sensors report plausible Values (either in the Infotainment System or the Instrument Cluster).		* Now drive the vehicle until all Wheel Pressure Sensors report plausible Values (either in the Infotainment System or the Instrument Cluster).
	* If the Sensors do not report proper values after a 30 Minute drive there may be a Problem with the Antennas, in such a case you should perform an Antenna Diagnosis.		* If the Sensors do not report proper values after a 30 Minute drive there may be a Problem with the Antennas, in such a case you should perform an Antenna Diagnosis.

			==== Special Notes ====

			* This forum thread goes into some detail on how this type of TPMS operates including meaning of Measuring Blocks:

			http://forums.ross-tech.com/showthread.php?4347

Dana at 15:14, 1 August 2014

2014-08-01T15:14:59Z

← Older revision		Revision as of 15:14, 1 August 2014
Line 10:		Line 10:
	Group 019<br>		Group 019<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	Check Field 1, it should show the Initialization Status 25.<br> ''If the Initialization has already been performed, skip the following Steps and directly start with driving the Vehicle. If it hasn't been performed, proceed with the Security Access followed by the Adaptation.''<br>		Check Field 1, it should show the Initialization Status. If the value is 25, no further diagnostic operations should be necessary before the test drive.<br> ''If the Initialization has already been performed, skip the following Steps and directly start with driving the Vehicle. If it hasn't been performed, proceed with the Security Access followed by the Adaptation.''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Security Access - 16]'''<br>		'''[Security Access - 16]'''<br>

Dana at 15:12, 1 August 2014

2014-08-01T15:12:41Z

← Older revision		Revision as of 15:12, 1 August 2014
Line 10:		Line 10:
	Group 019<br>		Group 019<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	Check Field 1, it should show the Initialization Status.<br> ''If the Initialization has already been performed, skip the following Steps and directly start with driving the Vehicle. If it hasn't been performed, proceed with the Security Access followed by the Adaptation.''<br>		Check Field 1, it should show the Initialization Status 25.<br> ''If the Initialization has already been performed, skip the following Steps and directly start with driving the Vehicle. If it hasn't been performed, proceed with the Security Access followed by the Adaptation.''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Security Access - 16]'''<br>		'''[Security Access - 16]'''<br>

Andy: /* Initialization */

2011-10-13T19:19:14Z

Initialization

← Older revision		Revision as of 19:19, 13 October 2011
Line 19:		Line 19:
	'''[Read]'''<br>		'''[Read]'''<br>
	Enter '''0''' as new Value.<br>		Enter '''0''' as new Value.<br>
			'''[Test]'''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	* Check the Tire Pressure for all 4/5 wheels and if necessary correct it.		* Check the Tire Pressure for all 4/5 wheels and if necessary correct it.

RtWiKiSyS0p at 16:46, 29 April 2009

2009-04-29T16:46:17Z

← Older revision		Revision as of 16:46, 29 April 2009
Line 10:		Line 10:
	Group 019<br>		Group 019<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	Check Field 1, it should show the Initialization Status. If the Initialization has already been performed skip the following Steps and directly start with driving the Vehicle. If it hasn't been performed proceed with the Security Access followed by the Adaptation.<br>		Check Field 1, it should show the Initialization Status.<br> ''If the Initialization has already been performed, skip the following Steps and directly start with driving the Vehicle. If it hasn't been performed, proceed with the Security Access followed by the Adaptation.''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Security Access - 16]'''<br>		'''[Security Access - 16]'''<br>

RtWiKiSyS0p at 16:45, 29 April 2009

2009-04-29T16:45:43Z

← Older revision		Revision as of 16:45, 29 April 2009
Line 10:		Line 10:
	Group 019<br>		Group 019<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	Check Field 1, it should show the Initialization Status. If the Initialization has already been performed skip the following Steps and directly start with driving the Vehicle.<br>		Check Field 1, it should show the Initialization Status. If the Initialization has already been performed skip the following Steps and directly start with driving the Vehicle. If it hasn't been performed proceed with the Security Access followed by the Adaptation.<br>
			'''[Done, Go Back]'''<br>
	'''[Security Access - 16]'''<br>		'''[Security Access - 16]'''<br>
	Enter 10896, to enable the Initilization.<br>		Enter 10896, to enable the Initilization.<br>

RtWiKiSyS0p at 16:45, 29 April 2009

2009-04-29T16:45:00Z

← Older revision		Revision as of 16:45, 29 April 2009
Line 7:		Line 7:
	'''[Select]'''<br>		'''[Select]'''<br>
	'''[65 - Tire Pressure Monitoring]'''<br>		'''[65 - Tire Pressure Monitoring]'''<br>
			'''[Measuring Blocks - 08]'''<br>
			Group 019<br>
			'''[Go!]'''<br>
			Check Field 1, it should show the Initialization Status. If the Initialization has already been performed skip the following Steps and directly start with driving the Vehicle.<br>
	'''[Security Access - 16]'''<br>		'''[Security Access - 16]'''<br>
	Enter 10896, to enable the Initilization.<br>		Enter 10896, to enable the Initilization.<br>
Line 28:		Line 32:
	'''[Close Controller, Go Back - 06]'''<br><br>		'''[Close Controller, Go Back - 06]'''<br><br>

	* Now drive the vehicle until all Wheel Pressure Sensors report plausible Values (either in the Infotainment System or the Instrument Cluster). If the Sensors do not report proper values after a 30 Minute drive there may be a Problem with the Antennas, in such a case you should perform an Antenna Diagnosis.		* Now drive the vehicle until all Wheel Pressure Sensors report plausible Values (either in the Infotainment System or the Instrument Cluster).
			* If the Sensors do not report proper values after a 30 Minute drive there may be a Problem with the Antennas, in such a case you should perform an Antenna Diagnosis.

RtWiKiSyS0p: New page: == Coding == == Special Procedures == === Initialization === '''[Select]'''
'''[65 - Tire Pressure Monitoring]'''
'''[Security Access - 16]'''
Enter 10896, to enable the Ini...

2009-04-29T16:42:25Z

New page: == Coding == == Special Procedures == === Initialization === '''[Select]''' '''[65 - Tire Pressure Monitoring]''' '''[Security Access - 16]''' Enter 10896, to enable the Ini...

New page

== Coding ==

== Special Procedures ==
=== Initialization ===

'''[Select]''' 
'''[65 - Tire Pressure Monitoring]''' 
'''[Security Access - 16]''' 
Enter 10896, to enable the Initilization. 
'''[Do it!]''' 
'''[Adaptation - 10]''' 
Adaptation Channel '''001''' 
'''[Read]''' 
Enter '''0''' as new Value. 
'''[Save]''' 
* Check the Tire Pressure for all 4/5 wheels and if necessary correct it.
Adaptation Channel '''004''' 
'''[Read]''' 
Enter '''1''' as new Value. 
'''[Save]''' 
'''[Done, Go Back]''' 
'''[Measuring Blocks - 08]''' 
Group 019 
'''[Go!]''' 
Check Field 1, it should show the Initialization Status. 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 

* Now drive the vehicle until all Wheel Pressure Sensors report plausible Values (either in the Infotainment System or the Instrument Cluster). If the Sensors do not report proper values after a 30 Minute drive there may be a Problem with the Antennas, in such a case you should perform an Antenna Diagnosis.

Bentley Continental (3W) Tire Pressure Monitoring - Revision history

Dana: /* Initialization */

Andy at 13:00, 22 March 2016

Dana at 15:14, 1 August 2014

Dana at 15:12, 1 August 2014

Andy: /* Initialization */

RtWiKiSyS0p at 16:46, 29 April 2009

RtWiKiSyS0p at 16:45, 29 April 2009

RtWiKiSyS0p at 16:45, 29 April 2009

RtWiKiSyS0p: New page: == Coding == == Special Procedures == === Initialization === '''[Select]''' '''[65 - Tire Pressure Monitoring]''' '''[Security Access - 16]''' Enter 10896, to enable the Ini...

RtWiKiSyS0p: New page: == Coding == == Special Procedures == === Initialization === '''[Select]'''
'''[65 - Tire Pressure Monitoring]'''
'''[Security Access - 16]'''
Enter 10896, to enable the Ini...