Immobilizer III Immobilizer Swapping (Instrument Cluster) - Revision history

Dana: /* Special Notes */

2014-07-30T18:38:09Z

Special Notes

← Older revision		Revision as of 18:38, 30 July 2014
Line 92:		Line 92:
	* Instructions for mileage entry on a new instrument cluster can be found here: [http://ross-tech.com/vag-com/cars/Non-Immo-cluster-swapping.html Non-Immo Instrument Cluster Swapping]		* Instructions for mileage entry on a new instrument cluster can be found here: [http://ross-tech.com/vag-com/cars/Non-Immo-cluster-swapping.html Non-Immo Instrument Cluster Swapping]
	** Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value!		** Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value!
			* If "Disabled" is shown in Adaptation Channel 050, the Instrument Cluster may have lock time. Check Measuring Blocks 022, 023 and 024.

	== Video Link ==		== Video Link ==

Andy: /* Instrument Cluster Swapping */

2014-07-23T21:08:33Z

Instrument Cluster Swapping

← Older revision		Revision as of 21:08, 23 July 2014
Line 47:		Line 47:
	* Battery voltage at least 12.0 V.		* Battery voltage at least 12.0 V.
	* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the REPLACEMENT (NEW or USED) cluster.		* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the REPLACEMENT (NEW or USED) cluster.
	** Immo 3 Audi vehicles typically use adaptation channels 060, ~~06 1and~~ 062 for the internal installation list since they do not have address 19-CAN Gateway. If in question, run a complete Adaptation [[Control Module Maps\| Control Module Map]] with the old module installed.		** Immo 3 Audi vehicles typically use adaptation channels 060, 061 and 062 for the internal installation list since they do not have address 19-CAN Gateway. If in question, run a complete Adaptation [[Control Module Maps\| Control Module Map]] with the old module installed.
	** Immo 3 VW vehicles typically use short coding in address 19-CAN Gateway. If the original value is 00006, which is common, recode the new unit to the same value to refresh the internal gateway installation list.		** Immo 3 VW vehicles typically use short coding in address 19-CAN Gateway. If the original value is 00006, which is common, recode the new unit to the same value to refresh the internal gateway installation list.
	* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the REPLACEMENT (NEW or USED) instrument cluster.		* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the REPLACEMENT (NEW or USED) instrument cluster.

Jef: /* Video Link */

2012-10-08T21:37:06Z

Video Link

← Older revision		Revision as of 21:37, 8 October 2012
Line 95:		Line 95:
	== Video Link ==		== Video Link ==

	Immobilizer Gen 3 ECM or Instrument Cluster swapping		=== Immobilizer Gen 3 ECM or Instrument Cluster swapping ===

	[[File:Wiki thumb nail.jpg\|200px\|link=http://www.youtube.com/watch?v=J5_51qeEyec]]		[[File:Wiki thumb nail.jpg\|200px\|link=http://www.youtube.com/watch?v=J5_51qeEyec]]

	http://www.youtube.com/watch?v=J5_51qeEyec		http://www.youtube.com/watch?v=J5_51qeEyec

Andy: /* Special Notes */

2012-09-11T21:09:18Z

Special Notes

← Older revision		Revision as of 21:09, 11 September 2012
Line 90:		Line 90:
	==== Special Notes ====		==== Special Notes ====

	* Instructions for mileage entry on a new instrument cluster can be found here: [http://~~www.~~ross-tech.com/vag-com/cars/~~Immo3~~-cluster-swapping.html ~~Procedure for installing a NEW~~ Instrument Cluster ~~in vehicles with Immobilizer III~~]		* Instructions for mileage entry on a new instrument cluster can be found here: [http://ross-tech.com/vag-com/cars/Non-Immo-cluster-swapping.html Non-Immo Instrument Cluster Swapping]
	** Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value!		** Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value!


	== Video Link ==		== Video Link ==

Jef: /* Special Notes */

2012-08-27T20:40:39Z

Special Notes

← Older revision		Revision as of 20:40, 27 August 2012
Line 92:		Line 92:
	* Instructions for mileage entry on a new instrument cluster can be found here: [http://www.ross-tech.com/vag-com/cars/Immo3-cluster-swapping.html Procedure for installing a NEW Instrument Cluster in vehicles with Immobilizer III]		* Instructions for mileage entry on a new instrument cluster can be found here: [http://www.ross-tech.com/vag-com/cars/Immo3-cluster-swapping.html Procedure for installing a NEW Instrument Cluster in vehicles with Immobilizer III]
	** Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value!		** Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value!


			== Video Link ==

			Immobilizer Gen 3 ECM or Instrument Cluster swapping

			[[File:Wiki thumb nail.jpg\|200px\|link=http://www.youtube.com/watch?v=J5_51qeEyec]]

			http://www.youtube.com/watch?v=J5_51qeEyec

Andy: /* Instrument Cluster Swapping */

2012-08-03T15:30:51Z

Instrument Cluster Swapping

← Older revision		Revision as of 15:30, 3 August 2012
Line 82:		Line 82:
	* '''Proceed with [[Immobilizer III Key Matching (Cluster)\|Key Matching]] now.'''		* '''Proceed with [[Immobilizer III Key Matching (Cluster)\|Key Matching]] now.'''

	* '''Enter the odometer reading using [http://ross-tech.com/vag-com/cars/Non-Immo-cluster-swapping.html these instructions from the Ross-Tech website] '''		* '''Enter the odometer reading (brand new clusters only) using [http://ross-tech.com/vag-com/cars/Non-Immo-cluster-swapping.html these instructions from the Ross-Tech website] '''

Andy: /* Instrument Cluster Swapping */

2012-08-03T15:29:46Z

Instrument Cluster Swapping

← Older revision		Revision as of 15:29, 3 August 2012
Line 81:		Line 81:

	* '''Proceed with [[Immobilizer III Key Matching (Cluster)\|Key Matching]] now.'''		* '''Proceed with [[Immobilizer III Key Matching (Cluster)\|Key Matching]] now.'''

			* '''Enter the odometer reading using [http://ross-tech.com/vag-com/cars/Non-Immo-cluster-swapping.html these instructions from the Ross-Tech website] '''





	==== Special Notes ====		==== Special Notes ====

Jef: /* Instrument Cluster Swapping */

2012-07-12T18:52:44Z

Instrument Cluster Swapping

← Older revision		Revision as of 18:52, 12 July 2012
Line 46:		Line 46:
	* The new or used cluster is installed in the car.		* The new or used cluster is installed in the car.
	* Battery voltage at least 12.0 V.		* Battery voltage at least 12.0 V.
	* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the ~~new~~ or ~~used~~ cluster.		* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the REPLACEMENT (NEW or USED) cluster.
	** Immo 3 Audi vehicles typically use adaptation channels 060, 06 1and 062 for the internal installation list since they do not have address 19-CAN Gateway. If in question, run a complete Adaptation [[Control Module Maps\| Control Module Map]] with the old module installed.		** Immo 3 Audi vehicles typically use adaptation channels 060, 06 1and 062 for the internal installation list since they do not have address 19-CAN Gateway. If in question, run a complete Adaptation [[Control Module Maps\| Control Module Map]] with the old module installed.
	** Immo 3 VW vehicles typically use short coding in address 19-CAN Gateway. If the original value is 00006, which is common, recode the new unit to the same value to refresh the internal gateway installation list.		** Immo 3 VW vehicles typically use short coding in address 19-CAN Gateway. If the original value is 00006, which is common, recode the new unit to the same value to refresh the internal gateway installation list.
	* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the ~~new~~ or ~~used~~ instrument cluster.		* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the REPLACEMENT (NEW or USED) instrument cluster.
	* Make sure to have the Radio Code (for factory radios only).		* Make sure to have the Radio Code (for factory radios only).

Line 58:		Line 58:

	'''[Login - 11]'''<br>		'''[Login - 11]'''<br>
	''For the following procedure, '''use the PIN of the NEW or USED''' instrument cluster~~.''<br>~~		''For the following procedure, '''use the PIN of the REPLACEMENT (NEW or USED)''' instrument cluster.''<br>
	~~''There are 2 possibilities how to enter a PIN, choose the one that applies for you~~. ''<br>
	* '''4-digit PIN'''		* '''4-digit PIN'''
	** Enter zero followed by the 4-digit PIN directly in the Login field. For example, if your PIN is 1234, enter 01234. <br>~~If you have a 4-digit PIN then you would '''NOT''' use the 7-digit PIN/SKC button at all~~		** Enter zero followed by the 4-digit PIN directly in the Login field. For example, if your PIN is 1234, enter 01234. <br>
	~~'''[Do it!]'''<br>~~
	~~---OR--- <br>~~
	* '''7-digit PIN'''
	** '''[Use 7-digit PIN/SKC]'''
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Do it!]'''<br>		'''[Do it!]'''<br>

Line 76:		Line 68:
	'''[Read]'''<br>		'''[Read]'''<br>
	''For the following procedure, '''use the PIN of the OLD (ORIGINAL)''' instrument cluster.''<br>		''For the following procedure, '''use the PIN of the OLD (ORIGINAL)''' instrument cluster.''<br>
	~~''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>~~
	* '''4-digit PIN'''		* '''4-digit PIN'''
	** Enter zero followed by the 4-digit PIN directly in the New Value field. For example, if your PIN is 1234, enter 01234. <br>~~If you have a 4-digit PIN then you would '''NOT''' use the 7-digit PIN/SKC button at all~~		** Enter zero followed by the 4-digit PIN directly in the New Value field. For example, if your PIN is 1234, enter 01234. <br>
	~~'''[Test]'''<br>~~
	~~'''[Save]'''<br>~~
	~~'''[Done, Go Back]'''<br>~~
	~~'''[Close Controller, Go Back - 06]'''<br>~~
	~~---OR--- <br>~~
	* '''7-digit PIN'''
	** '''[Use 7-digit PIN/SKC]'''
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''
	** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Test]'''<br>		'''[Test]'''<br>
			* The values may change to "32000", this is normal
	'''[Save]'''<br>		'''[Save]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>


	* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.		* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
	* Verify that the ~~new~~ or ~~used~~ instrument cluster now shows the VIN/IMMO-ID of the vehicle now.		* Verify that the REPLACEMENT (NEW or USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now.

Jef: /* Instrument Cluster Swapping (Used Cluster) */

2012-07-12T18:07:26Z

Instrument Cluster Swapping (Used Cluster)

← Older revision		Revision as of 18:07, 12 July 2012
Line 41:		Line 41:


	== Instrument Cluster Swapping ~~(Used Cluster)~~ ==		== Instrument Cluster Swapping ==

	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* The ~~NEW (USED)~~ cluster is installed in the car.		* The new or used cluster is installed in the car.
	* Battery voltage at least 12.0 V.		* Battery voltage at least 12.0 V.
	* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the ~~NEW (USED)~~ cluster.		* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the new or used cluster.
	** Immo 3 Audi vehicles typically use adaptation channels 060, 06 1and 062 for the internal installation list since they do not have address 19-CAN Gateway. If in question, run a complete Adaptation [[Control Module Maps\| Control Module Map]] with the old module installed.		** Immo 3 Audi vehicles typically use adaptation channels 060, 06 1and 062 for the internal installation list since they do not have address 19-CAN Gateway. If in question, run a complete Adaptation [[Control Module Maps\| Control Module Map]] with the old module installed.
	** Immo 3 VW vehicles typically use short coding in address 19-CAN Gateway. If the original value is 00006, which is common, recode the new unit to the same value to refresh the internal gateway installation list.		** Immo 3 VW vehicles typically use short coding in address 19-CAN Gateway. If the original value is 00006, which is common, recode the new unit to the same value to refresh the internal gateway installation list.
	* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the ~~NEW (USED)~~ instrument cluster.		* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the new or used instrument cluster.
	* Make sure to have the Radio Code (for factory radios only).		* Make sure to have the Radio Code (for factory radios only).

Line 58:		Line 58:

	'''[Login - 11]'''<br>		'''[Login - 11]'''<br>
	''For the following procedure, '''use the PIN of the NEW (USED)''' instrument cluster.''<br>		''For the following procedure, '''use the PIN of the NEW or USED''' instrument cluster.''<br>
	''There are 2 possibilities how to enter a PIN, choose the one that applies for you. ''<br>		''There are 2 possibilities how to enter a PIN, choose the one that applies for you. ''<br>
	* '''4-digit PIN'''		* '''4-digit PIN'''
Line 96:		Line 96:

	* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.		* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
	* Verify that the ~~NEW (USED)~~ instrument cluster now shows the VIN/IMMO-ID of the vehicle now.		* Verify that the new or used instrument cluster now shows the VIN/IMMO-ID of the vehicle now.

Dana at 20:50, 27 April 2012

2012-04-27T20:50:26Z

← Older revision		Revision as of 20:50, 27 April 2012
Line 48:		Line 48:
	* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster.		* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster.
	** Immo 3 Audi vehicles typically use adaptation channels 060, 06 1and 062 for the internal installation list since they do not have address 19-CAN Gateway. If in question, run a complete Adaptation [[Control Module Maps\| Control Module Map]] with the old module installed.		** Immo 3 Audi vehicles typically use adaptation channels 060, 06 1and 062 for the internal installation list since they do not have address 19-CAN Gateway. If in question, run a complete Adaptation [[Control Module Maps\| Control Module Map]] with the old module installed.
			** Immo 3 VW vehicles typically use short coding in address 19-CAN Gateway. If the original value is 00006, which is common, recode the new unit to the same value to refresh the internal gateway installation list.
	* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.		* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.
	* Make sure to have the Radio Code (for factory radios only).		* Make sure to have the Radio Code (for factory radios only).