Immobilizer II ECU Swapping - Revision history

Dana at 15:51, 5 May 2014

2014-05-05T15:51:26Z

← Older revision		Revision as of 15:51, 5 May 2014
Line 38:		Line 38:
	== Coding ==		== Coding ==
	The new module will need to be coded. Enter the coding from the original module if possible. If the original module is not available, or did not communicate, refer to the coding chart in VCDS or the factory repair manual.		The new module will need to be coded. Enter the coding from the original module if possible. If the original module is not available, or did not communicate, refer to the coding chart in VCDS or the factory repair manual.


			==== Special Notes ====
			On some Gasoline engines you may need to complete the [[Throttle Body Alignment (TBA)]]

Dana at 21:49, 24 April 2013

2013-04-24T21:49:30Z

← Older revision		Revision as of 21:49, 24 April 2013
Line 23:		Line 23:

	* On some Euro Audi models with Immobilizer 2, the PIN/SKC will be required.		* On some Euro Audi models with Immobilizer 2, the PIN/SKC will be required.
	* On NAR market Cabrio models produced after 05/1999 the PIN/SKC may be required.		* On NAR market Cabrio models produced after 05/1999 the PIN/SKC may be required. This split is noted [[Immobilizer#Immobilizer_Generation_2 \|here]]

	== Activating Cruise Control on a new ECU (DBW) ==		== Activating Cruise Control on a new ECU (DBW) ==

Dana at 17:40, 7 June 2011

2011-06-07T17:40:44Z

← Older revision		Revision as of 17:40, 7 June 2011
Line 23:		Line 23:

	* On some Euro Audi models with Immobilizer 2, the PIN/SKC will be required.		* On some Euro Audi models with Immobilizer 2, the PIN/SKC will be required.
			* On NAR market Cabrio models produced after 05/1999 the PIN/SKC may be required.

	== Activating Cruise Control on a new ECU (DBW) ==		== Activating Cruise Control on a new ECU (DBW) ==

Dana at 20:24, 28 April 2011

2011-04-28T20:24:42Z

← Older revision		Revision as of 20:24, 28 April 2011
Line 32:		Line 32:
	Enter 11463 to activate cruise control<br>		Enter 11463 to activate cruise control<br>
	'''[Do It!]'''<br>		'''[Do It!]'''<br>

			Note: See this page for additional CCS details: [[Checking Cruise Control using Measuring Values]]

			== Coding ==
			The new module will need to be coded. Enter the coding from the original module if possible. If the original module is not available, or did not communicate, refer to the coding chart in VCDS or the factory repair manual.

Dana at 22:02, 18 March 2011

2011-03-18T22:02:21Z

← Older revision		Revision as of 22:02, 18 March 2011
Line 14:		Line 14:
	'''[Read]'''<br>		'''[Read]'''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	~~<br>~~
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>
	'''[Exit]'''<br>		'''[Exit]'''<br>
	~~<br>~~		Turn ignition OFF for 15 seconds. Start vehicle.<br>
	Turn ignition OFF for 15 seconds. Start vehicle.
	<br>
	~~<br>~~
	Notes:		Notes:
			* For cars with a separate Immobilizer (Includes 2000+ EuroVan, Cabrio, and many older non-US models), use '''[25 Immobilizer]''' instead of '''[17 - Instruments]'''. The rest of the procedure is the same.

			* On some Euro Audi models with Immobilizer 2, the PIN/SKC will be required.

	* For cars with a ~~separate Immobilizer~~ (~~Includes 2000+ EuroVan, Cabrio, and many older non-US models~~)~~, use~~ '''~~[25 Immobilizer]~~''~~' instead of '''[17~~ - ~~Instruments]'''. The rest of the procedure is the same~~.		== Activating Cruise Control on a new ECU (DBW) ==
			DBW (''Drive-by-Wire'') Factory fresh ECU's often come with cruise control de-activated.<br>

	* On some Euro Audi models with Immobilizer 2, a PIN will be required.		'''[Select]'''<br>
			'''[01 - Engine]'''<br>
			'''[Login - 11]'''<br>
			Enter 11463 to activate cruise control<br>
			'''[Do It!]'''<br>

Jef: /* ECM Matching */

2010-09-10T21:47:11Z

ECM Matching

← Older revision		Revision as of 21:47, 10 September 2010
Line 20:		Line 20:
	<br>		<br>
	Turn ignition OFF for 15 seconds. Start vehicle.		Turn ignition OFF for 15 seconds. Start vehicle.
			<br>
			<br>
			Notes:

			* For cars with a separate Immobilizer (Includes 2000+ EuroVan, Cabrio, and many older non-US models), use '''[25 Immobilizer]''' instead of '''[17 - Instruments]'''. The rest of the procedure is the same.

			* On some Euro Audi models with Immobilizer 2, a PIN will be required.

Jef: Created page with '''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk. As always, you should refer to …'

2010-09-10T21:35:13Z

Created page with '''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk. As always, you should refer to …'

New page

''Ross-Tech is not responsible for any damage or problems that may result from following these instructions. They are to be used at your own risk. As always, you should refer to a Factory Repair Manual for your vehicle!''

== ECM Matching ==

'''Prerequisites:''' 

* Battery voltage at least 12.5 V. 
* Immobilizer II ECM

'''[Select]''' 
'''[17 - Instruments]''' 
'''[Adaption - 10]''' 
Leave channel at "00" 
'''[Read]''' 
'''[Save]''' 
 
'''[Done, Go Back]''' 
'''[Close Controller, Go Back - 06]''' 
'''[Exit]''' 
 
Turn ignition OFF for 15 seconds. Start vehicle.