Immobilizer IV Key Matching - Revision history

Dana at 19:44, 3 June 2024

2024-06-03T19:44:00Z

← Older revision		Revision as of 19:44, 3 June 2024
Line 98:		Line 98:
	Note; If a original matched key is NOT present in a VW Passat (3C) vehicle please see this forum entry:		Note; If a original matched key is NOT present in a VW Passat (3C) vehicle please see this forum entry:
	http://forums.ross-tech.com/showthread.php?4386-Passat-B6-Key-Matching&p=42718&viewfull=1#post42718		http://forums.ross-tech.com/showthread.php?4386-Passat-B6-Key-Matching&p=42718&viewfull=1#post42718



			== Special Notes ==
			If Adaptation Channel 001 is not saving when the PIN is confirmed to be correct make sure the WSC/Importer/Equipment numbers are NOT all zeros before clicking Save. If address 25-Immobilizer shows all zero details (Shop #: WSC 00000 000 00000) in the Auto-Scan after failed matching they can be changed on the VCDS program [https://www.ross-tech.com/vcds/tour/option_screen.php#WSC [Options]] screen. Any value that is not all zeros or ones should work.

Dana: /* VW Passat (3C) Immobilizer Key Matching */

2015-10-25T17:31:49Z

VW Passat (3C) Immobilizer Key Matching

← Older revision		Revision as of 17:31, 25 October 2015
Line 95:		Line 95:
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>
	<font color=white>ST?ID=53293</font><br>		<font color=white>ST?ID=53293</font><br>

			Note; If a original matched key is NOT present in a VW Passat (3C) vehicle please see this forum entry:
			http://forums.ross-tech.com/showthread.php?4386-Passat-B6-Key-Matching&p=42718&viewfull=1#post42718

Dana at 13:41, 15 September 2014

2014-09-15T13:41:46Z

← Older revision		Revision as of 13:41, 15 September 2014
Line 17:		Line 17:

	'''<u>Prerequisites:</u>'''<br>		'''<u>Prerequisites:</u>'''<br>
	* All keys are either new or were adapted to this car (IMMO-ID) before.<br>		* All keys are either brand new or were adapted to this car (IMMO-ID) before.<br>
	* You can match up to 8 keys.		* You can match up to 8 keys.
	* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''		* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''
	* Battery voltage at least 12.0 V.<br>		* Battery voltage at least 12.0 V.<br>


	'''[Select]'''<br>		'''[Select]'''<br>
Line 30:		Line 29:
	''The value in field 3 must be '''Yes'''. If value is '''No''', the key is not capable of being adapted to Immobilizer.''<br>		''The value in field 3 must be '''Yes'''. If value is '''No''', the key is not capable of being adapted to Immobilizer.''<br>
	''You can check each key in this manner.''		''You can check each key in this manner.''


	Select Block '''003'''.<br>		Select Block '''003'''.<br>
Line 40:		Line 38:
	''If lockout time was present check Group 1.3 as mentioned above to confirm "Yes" is shown.''<br>		''If lockout time was present check Group 1.3 as mentioned above to confirm "Yes" is shown.''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>


	'''[Security Access - 16]'''<br>		'''[Security Access - 16]'''<br>
Line 46:		Line 43:
	** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''		** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
	'''[Do it!]'''<br>		'''[Do it!]'''<br>


	'''[Adaptation - 10]'''<br>		'''[Adaptation - 10]'''<br>
Line 64:		Line 60:

	'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''		'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''

			----

	== VW Passat (3C) Immobilizer Key Matching ==		== VW Passat (3C) Immobilizer Key Matching ==
			'''<u>Prerequisites:</u>'''<br>
			* At least one original matched key is present.<br>
			* All keys are either brand new (meaning ordered by VIN at the VW Dealer) or were adapted to this car (IMMO-ID) before.<br>
			* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.''<br>
			* Battery voltage at least 12.0 V.<br>

	The Prerequisites ~~and basic steps~~ above apply to the [[VW Passat (3C) Immobilizer]] system however the Instrument Cluster may begin by showing 0-2 (using a 2 key example) so the 1st key may need to be reinserted as follows:		The Measuring block Prerequisites above apply to the [[VW Passat (3C) Immobilizer]] system however the Instrument Cluster may begin by showing 0-2 (using a 2 key example) so the 1st key may need to be reinserted as follows:

			'''[Select]'''<br>
			'''[25 - Immobilizer]'''<br>
	'''[Security Access - 16]'''<br>		'''[Security Access - 16]'''<br>
	* '''4-digit PIN'''		* '''4-digit PIN'''
Line 80:		Line 85:
	'''[Test]'''<br>		'''[Test]'''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	* Repeat the following steps until all keys have been matched:<br>		* DO NOT exit the control module. Repeat the following steps until all keys have been matched:<br>
	**Observe the Instrument cluster display for feedback related to the key position and the total number of keys.		**Observe the Instrument cluster display for feedback related to the key position and the total number of keys.
	***For example '''0-2''' means zero of the two total keys were learned. If this is the case you will need to reinsert that key to match it to position #1.<br>		***For example '''0-2''' means zero of the two total keys were learned. If this is the case you will need to reinsert that key to match it to position #1.<br>
Line 86:		Line 91:
	**Switch ignition off and remove key.''<br>		**Switch ignition off and remove key.''<br>
	**Insert next key to ignition and switch ignition on again.<br>		**Insert next key to ignition and switch ignition on again.<br>
	''Observe the Instrument cluster display for feedback related to the key position again and repeat until all keys are matched'.<br>		''Observe the Instrument cluster display for feedback related to the key position again and repeat until all keys are matched''.<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>
	'''[Close Controller, Go Back - 06]'''<br>		'''[Close Controller, Go Back - 06]'''<br>
			<font color=white>ST?ID=53293</font><br>

Dana at 14:08, 12 September 2014

2014-09-12T14:08:46Z

← Older revision		Revision as of 14:08, 12 September 2014
Line 64:		Line 64:

	'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''		'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''

			== VW Passat (3C) Immobilizer Key Matching ==

			The Prerequisites and basic steps above apply to the [[VW Passat (3C) Immobilizer]] system however the Instrument Cluster may begin by showing 0-2 (using a 2 key example) so the 1st key may need to be reinserted as follows:

			'''[Security Access - 16]'''<br>
			* '''4-digit PIN'''
			** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
			'''[Do it!]'''<br>
			'''[Adaptation - 10]'''<br>
			Enter 001 in "Channel Number".<br>
			'''[Read]'''<br>
			''The "Stored Value" is the number of keys currently matched.''<br>
			Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br>
			'''[Test]'''<br>
			'''[Save]'''<br>
			* Repeat the following steps until all keys have been matched:<br>
			**Observe the Instrument cluster display for feedback related to the key position and the total number of keys.
			***For example '''0-2''' means zero of the two total keys were learned. If this is the case you will need to reinsert that key to match it to position #1.<br>
			*** Alternatively, '''1-2''' would mean one of the two total keys were learned. It this is the case you do NOT have to reinsert that key because it was already learned and matched to position #1.<br>
			**Switch ignition off and remove key.''<br>
			**Insert next key to ignition and switch ignition on again.<br>
			''Observe the Instrument cluster display for feedback related to the key position again and repeat until all keys are matched'.<br>
			'''[Done, Go Back]'''<br>
			'''[Close Controller, Go Back - 06]'''<br>

Jef: /* Key Matching */

2012-07-12T22:13:03Z

Key Matching

← Older revision		Revision as of 22:13, 12 July 2012
Line 43:		Line 43:

	'''[Security Access - 16]'''<br>		'''[Security Access - 16]'''<br>
	~~''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''~~
	* '''4-digit PIN'''		* '''4-digit PIN'''
	** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''		** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
	* '''7-digit PIN'''
	** '''[Use 7-digit PIN/SKC]'''
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''
	** VCDS will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Do it!]'''<br>		'''[Do it!]'''<br>

Peter: /* Key Matching */

2012-06-07T15:22:10Z

Key Matching

← Older revision		Revision as of 15:22, 7 June 2012
Line 59:		Line 59:
	''The "Stored Value" is the number of keys currently matched.''<br>		''The "Stored Value" is the number of keys currently matched.''<br>
	Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br>		Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br>
	''The old keys are automatically ~~beeing~~ cleared.''<br>		''The old keys are automatically being cleared.''<br>
	'''[Save]'''<br>		'''[Save]'''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>

Dana at 13:17, 6 July 2011

2011-07-06T13:17:08Z

← Older revision		Revision as of 13:17, 6 July 2011
Line 26:		Line 26:
	'''[25 - Immobilizer]'''<br>		'''[25 - Immobilizer]'''<br>
	'''[Meas. Blocks - 08]'''<br>		'''[Meas. Blocks - 08]'''<br>
	Select Block 001.<br>		Select Block '''001'''.<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	''The value in field 3 must be '''Yes'''. If value is '''No''', the key is not capable of being adapted to Immobilizer.''<br>		''The value in field 3 must be '''Yes'''. If value is '''No''', the key is not capable of being adapted to Immobilizer.''<br>
Line 32:		Line 32:


	Select Block 003.<br>		Select Block '''003'''.<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	''Make sure the shown lock times in field 1, 2 and 3 are '''0''' (each field represents a time in minutes).''<br>		''Make sure the shown lock times in field 1, 2 and 3 are '''0''' (each field represents a time in minutes).''<br>
Line 38:		Line 38:
	** ''Do NOT switch off the ignition!''		** ''Do NOT switch off the ignition!''
	** ''Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.''		** ''Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.''
			''If lockout time was present check Group 1.3 as mentioned above to confirm "Yes" is shown.''<br>
	'''[Done, Go Back]'''<br>		'''[Done, Go Back]'''<br>

Line 49:		Line 50:
	** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.		** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
	** '''[OK]'''		** '''[OK]'''
	** ~~VAG-COM~~ will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".		** VCDS will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
	'''[Do it!]'''<br>		'''[Do it!]'''<br>

Florian at 08:59, 16 June 2011

2011-06-16T08:59:03Z

← Older revision		Revision as of 08:59, 16 June 2011
Line 66:		Line 66:
	**''Switch ignition off and remove key.''<br>		**''Switch ignition off and remove key.''<br>
	**''Insert next key to ignition and switch ignition on again.''<br>		**''Insert next key to ignition and switch ignition on again.''<br>
	**''The warning light for the Immobilizer will light up for ~2 seconds, then go out ~~Switch ignition off and remove key~~.''<br>		**''The warning light for the Immobilizer will light up for ~2 seconds, then go out.''<br>

	'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''		'''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''

RtWiKiSyS0p at 22:24, 5 January 2007

2007-01-05T22:24:13Z

← Older revision		Revision as of 22:24, 5 January 2007
Line 28:		Line 28:
	Select Block 001.<br>		Select Block 001.<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	''The value in field 3 must be 1. If value is ~~not 1~~, the key is not capable of being adapted to Immobilizer.''<br>		''The value in field 3 must be '''Yes'''. If value is '''No''', the key is not capable of being adapted to Immobilizer.''<br>
	''You can check each key in this manner.''		''You can check each key in this manner.''

RtWiKiSyS0p at 13:36, 14 December 2006

2006-12-14T13:36:31Z

← Older revision		Revision as of 13:36, 14 December 2006
Line 26:		Line 26:
	'''[25 - Immobilizer]'''<br>		'''[25 - Immobilizer]'''<br>
	'''[Meas. Blocks - 08]'''<br>		'''[Meas. Blocks - 08]'''<br>
	Select Block ~~002~~.<br>		Select Block 001.<br>
	'''[Go!]'''<br>		'''[Go!]'''<br>
	''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br>		''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br>