RtWiKiSyS0p at 15:36, 13 March 2011

2011-03-13T15:36:26Z

← Older revision		Revision as of 15:36, 13 March 2011
Line 8:		Line 8:
	Component: J533__Gateway H16 0202		Component: J533__Gateway H16 0202

	In this Example the Software Part Number is 1K0-907-530-Q, only Gateways with this Part Number (or newer) are known to be compatible with the RNS310		In this Example the Software Part Number is 1K0-907-530-Q, only Gateways with this Part Number (or newer) are known to be compatible with the RNS310. For the VW Passat (3C) only Gateways with the Part Number 3C0-907-530-E (or newer) are known to be compatible.

	== Installation & Wiring ==		== Installation & Wiring ==

RtWiKiSyS0p: Created page with '== Requirements == === Gateway === The Gateway (aka. Diagnostic Interface for Databus OR CAN-Gateway) is responsible for passing Messages from one Control Module to another, old…'

2011-03-13T15:34:19Z

Created page with '== Requirements == === Gateway === The Gateway (aka. Diagnostic Interface for Databus OR CAN-Gateway) is responsible for passing Messages from one Control Module to another, old…'

New page

== Requirements ==
=== Gateway ===

The Gateway (aka. Diagnostic Interface for Databus OR CAN-Gateway) is responsible for passing Messages from one Control Module to another, older versions of the Gateways were not compatible and wouldn't allow a Diagnostic Tool like VCDS to communicate with the new Radio Navigation System.

Address 19: CAN Gateway Labels: 1K0-907-530.lbl
Part No SW: '''1K0 907 530 Q''' HW: 1K0 907 951
Component: J533__Gateway H16 0202

In this Example the Software Part Number is 1K0-907-530-Q, only Gateways with this Part Number (or newer) are known to be compatible with the RNS310

== Installation & Wiring ==

Additional Information can be found in the Repair Manuals, the Wiring Diagrams, the Parts Catalog and/or the Instructions included in the Retrofitting Kit.

== Configuration ==

The following Activations are necessary to ensure that the newly fitted parts are properly recognized and are ready to use.

* '''Update the Installation List in the Gateway (J533 / #19).'''
** Register the newly added '''37 - Navigation''' Control Module, in case you had a Navigation System installed before the Retrofit this step may not be necessary. Address '''56 - Radio''' should also be activated in case there was no Radio installed prior to the Retrofit. ''Even though Address '''56 - Radio''' is registered, the RNS310 will NOT communicate via that Address - you have to use '''37 - Navigation''' instead.''
* '''Update the Navigation System (J506 / #37) Coding.'''
** ''Due to different Control Modules and Equipment in the Car the actual Coding Table is not shown here but will automatically be used by the Long Coding Assistant once you access the Function using VCDS.''
** ''Make sure to enter a Plausible WorkShopCode (WSC) like 12345-123-12345 on the Coding Screen, new or reflashed RNS510 units may have a WSC 00000-000-00000 stored which results in a [[01042|01042 - Control Module Not Coded]] Fault Code.

'''''If you are having trouble finding/calculating the proper Coding using the Long Coding Assist [http://ross-tech.com/contact.html please Contact us directly].''' Make sure to include a complete Diagnostic Protocol (Auto-Scan) from the Car and state which steps/work you have performed yet.''

Navigation System (RNS310) Retrofitting - Revision history

RtWiKiSyS0p at 15:36, 13 March 2011

RtWiKiSyS0p: Created page with '== Requirements == === Gateway === The Gateway (aka. Diagnostic Interface for Databus OR CAN-Gateway) is responsible for passing Messages from one Control Module to another, old…'