User talk:Jef - Revision history

Jef at 22:11, 9 February 2024

2024-02-09T22:11:56Z

← Older revision		Revision as of 22:11, 9 February 2024
Line 1:		Line 1:
	This information applies to the MQB platform with the Steering Angle Sensor (G85) ~~intigraged~~ into the Steering Assist (J500). This can be identified by evaluating the data in the Auto-Scan:		This information applies to the MQB platform with the Steering Angle Sensor (G85) integrated into the Steering Assist (J500). This can be identified by evaluating the data in the Auto-Scan:

	Address 44: Steering Assist (J500) Labels:\| 5Q0-909-144.clb		Address 44: Steering Assist (J500) Labels:\| 5Q0-909-144.clb

Jef at 22:08, 9 February 2024

2024-02-09T22:08:20Z

← Older revision		Revision as of 22:08, 9 February 2024
Line 1:		Line 1:
			This information applies to the MQB platform with the Steering Angle Sensor (G85) intigraged into the Steering Assist (J500). This can be identified by evaluating the data in the Auto-Scan:

	Address 44: Steering Assist (J500) Labels:\| 5Q0-909-144.clb		Address 44: Steering Assist (J500) Labels:\| 5Q0-909-144.clb
	Part No SW: 3Q0 909 144 K HW: 3Q0 909 144 H		Part No SW: 3Q0 909 144 K HW: 3Q0 909 144 H
	Component: '''EPS_MQB_ZFLS''' 506 5072		Component: '''EPS_MQB_ZFLS''' 506 5072

			*If '''EPS_MQB_ZFLS''' is not shown in the Component field, this information may not apply.

	== Basic Setting ==		== Basic Setting ==

Jef at 21:51, 9 February 2024

2024-02-09T21:51:48Z

← Older revision		Revision as of 21:51, 9 February 2024
Line 1:		Line 1:
	Address 44: Steering Assist (J500) Labels:\| 5Q0-909-144.clb		Address 44: Steering Assist (J500) Labels:\| 5Q0-909-144.clb
	Part No SW: 3Q0 909 144 K HW: 3Q0 909 144 H		Part No SW: 3Q0 909 144 K HW: 3Q0 909 144 H
	Component: EPS_MQB_ZFLS 506 5072		Component: '''EPS_MQB_ZFLS''' 506 5072

Jef at 21:45, 9 February 2024

2024-02-09T21:45:05Z

← Older revision		Revision as of 21:45, 9 February 2024
Line 1:		Line 1:
	Address 44: Steering Assist (J500) Labels:\| 5Q0-909-144.clb		Address 44: Steering Assist (J500) Labels:\| 5Q0-909-144.clb
	Part No SW: 3Q0 909 144 K HW: 3Q0 909 144 H		Part No SW: 3Q0 909 144 K HW: 3Q0 909 144 H
	Component: EPS_MQB_ZFLS 506 5072		Component: EPS_MQB_ZFLS 506 5072

Jef at 21:44, 9 February 2024

2024-02-09T21:44:52Z

← Older revision		Revision as of 21:44, 9 February 2024
Line 1:		Line 1:
			Address 44: Steering Assist (J500) Labels:\| 5Q0-909-144.clb
			Part No SW: 3Q0 909 144 K HW: 3Q0 909 144 H
			Component: EPS_MQB_ZFLS 506 5072



			== Basic Setting ==

			=== Sensor for Steering Angle (G85) ===

			'''<u>Prerequisites:</u>'''<br>
			* Start the vehicle.<br>

			'''[44-Steering Assist]'''<br>
			'''[Security Access - 16]'''<br>
			*Enter 19249<br>
			'''[Basic Settings - 04]'''<br>
			*'''[MAS00815] Steering angle sensor'''<br>
			'''[Go!]'''<br>
			*Rotate steering wheel all the way to the left, hold firmly against end stop for 5 seconds.<br>
			*Rotate steering wheel all the way to the right, hold firmly against end stop for 5 seconds.<br>
			*Center steering wheel, front wheel straight ahead.<br>
			'''[Stop]'''<br>
			*Several error messages and warnings will appear on the cluster, what messages you get can vary based on how the vehicles is equipped.<br>
			'''[Done, Go Back]'''<br>
			*Rotate steering wheel all the way to the left, hold firmly against end stop for 5 seconds.<br>
			*Rotate steering wheel all the way to the right, hold firmly against end stop for 5 seconds.<br>
			*Center steering wheel, front wheel straight ahead.<br>
			'''[Close Controller, Go Back - 06]'''<br>
			*Cycle the ignition off for 10 seconds.<br>
			<br>
			'''Notes'''
			*When doing the Basic Settings, should see the message of "Running", but it may not change to "Finished Correctly"
			*Several control modules will flag DTCs, "Databus" type codes that can cleared out after the 10 second ignition cycle.<br>

			== Video Link ==

			[[File:MBQ_G85_thumb_wiki.jpg\|200px\|link=https://www.youtube.com/watch?v=bXScTl4VvMc]]

			https://www.youtube.com/watch?v=bXScTl4VvMc













	'''[Select]'''<br>		'''[Select]'''<br>
	'''[15 - Airbags]'''<br>		'''[15 - Airbags]'''<br>

Jef at 18:32, 5 April 2023

2023-04-05T18:32:34Z

← Older revision		Revision as of 18:32, 5 April 2023
Line 20:		Line 20:
	** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance		** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance
	*** Not all systems have location IDE03873-ENG99733		*** Not all systems have location IDE03873-ENG99733
	It can be normal for one of those locations to be a value of 0 pF, but if two of those locations are 0 pF, it ~~can~~ be a sign of a failed pressure mat that needs to be replaced.		It can be normal for one of those locations to be a value of 0 pF, but if two of those locations are 0 pF, it may be a sign of a failed pressure mat that needs to be replaced.
	* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.		* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.

Jef at 18:32, 5 April 2023

2023-04-05T18:32:14Z

← Older revision		Revision as of 18:32, 5 April 2023
Line 20:		Line 20:
	** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance		** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance
	*** Not all systems have location IDE03873-ENG99733		*** Not all systems have location IDE03873-ENG99733
	It can be normal for one of those locations to be a value of 0 pF, but if two of those locations are 0 pF, it can be a sign of a failed pressure mat that needs to be replaced~~. We would appreciate feedback on this if possible~~.		It can be normal for one of those locations to be a value of 0 pF, but if two of those locations are 0 pF, it can be a sign of a failed pressure mat that needs to be replaced.
	* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.		* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.

Jef at 18:31, 5 April 2023

2023-04-05T18:31:59Z

← Older revision		Revision as of 18:31, 5 April 2023
Line 20:		Line 20:
	** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance		** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance
	*** Not all systems have location IDE03873-ENG99733		*** Not all systems have location IDE03873-ENG99733
	It can be normal for one of those locations to be a value of 0 pF, but if two of those locations are 0 pF, it can be a sign of a failed pressure mat that needs to be replaced.		It can be normal for one of those locations to be a value of 0 pF, but if two of those locations are 0 pF, it can be a sign of a failed pressure mat that needs to be replaced. We would appreciate feedback on this if possible.
	* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.		* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.

Jef at 18:31, 5 April 2023

2023-04-05T18:31:15Z

← Older revision		Revision as of 18:31, 5 April 2023
Line 19:		Line 19:
	** IDE03872-ENG99733,Seat occupied recognition imaginary part-Measured Value Capacitance		** IDE03872-ENG99733,Seat occupied recognition imaginary part-Measured Value Capacitance
	** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance		** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance
	If all of ~~these~~ value are 0 pF, ~~then~~ it ~~is recommend to replace the~~ pressure mat ~~in the passenger seat~~.		*** Not all systems have location IDE03873-ENG99733
			It can be normal for one of those locations to be a value of 0 pF, but if two of those locations are 0 pF, it can be a sign of a failed pressure mat that needs to be replaced.
	* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.		* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.

Jef at 16:52, 5 April 2023

2023-04-05T16:52:17Z

← Older revision		Revision as of 16:52, 5 April 2023
Line 19:		Line 19:
	** IDE03872-ENG99733,Seat occupied recognition imaginary part-Measured Value Capacitance		** IDE03872-ENG99733,Seat occupied recognition imaginary part-Measured Value Capacitance
	** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance		** IDE03873-ENG99733,Seat occupied recognition compensated imaginary part-Measured Value Capacitance
	If ~~any~~ of these value are ~~less than XX~~ pF, then it is ~~recommened~~ to replace the pressure mat in the passenger seat.		If all of these value are 0 pF, then it is recommend to replace the pressure mat in the passenger seat.
	* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.		* We had a repair facility report a Battery Disconnect was required when matching a brand new PODS module to the original Airbag controller when working on a 2011 Jetta Sedan.