VW Golf (5K) Body Control Module - Revision history

Dana at 18:43, 25 July 2023

2023-07-25T18:43:34Z

← Older revision		Revision as of 18:43, 25 July 2023
Line 41:		Line 41:
	* Start Matching new/additional Remote Controls with entering the number of new remotes (2 ''in most cases''), then '''Test''' and '''Save''' the New Value.		* Start Matching new/additional Remote Controls with entering the number of new remotes (2 ''in most cases''), then '''Test''' and '''Save''' the New Value.
	* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers should light up to confirm the Adaptation Process of each Remote Control.		* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers should light up to confirm the Adaptation Process of each Remote Control.
	Note: ''Adaptation Channel 001 may not be applicable to a BCM installed in a KESSY (Address; 05-Acc/Start Auth. control module) equipped vehicle. If Channel 001 is not available, the vehicle key, (with integrated or non-removable remote) should be automatically matched when performing [[Immobilizer#Immobilizer Generation 4 \| Immobilizer 4+]] matching. We do not have a procedure for this configuration and recommend Dealer matching if [[Official Factory Repair Information \| Immobilizer and Pass-Thru]] options are not available.''		Note: '''Adaptation Channel 001 may not be applicable to a BCM installed in a KESSY (Address; 05-Acc/Start Auth. control module) equipped vehicle'''. ''If Channel 001 is not available, the vehicle key, (with integrated or non-removable remote) should be automatically matched when performing [[Immobilizer#Immobilizer Generation 4 \| Immobilizer 4+]] matching. We do not have a procedure for this configuration and recommend Dealer matching if [[Official Factory Repair Information \| Immobilizer and Pass-Thru]] options are not available.''

	=== Channel 019: Factory Mode ===		=== Channel 019: Factory Mode ===

Dana at 17:18, 6 December 2016

2016-12-06T17:18:33Z

← Older revision		Revision as of 17:18, 6 December 2016
Line 1:		Line 1:
	__FORCETOC__		__FORCETOC__
			This page applies to Address '''09-Cent. Elect. (J519)''' in models using a BCM with '''PQ35''' in the Component field:

			Address 09: Cent. Elect. (J519) Labels: 1K0-937-08x-09.clb
			Part No SW: 1K0 937 084 G HW: 1K0 937 084 G
			Component: BCM '''PQ35''' B 110 0651

			Address 09: Cent. Elect. (J519) Labels: 1K0-937-08x-09.clb
			Part No SW: 5K0 937 086 L HW: 5K0 937 086 L
			Component: BCM '''PQ35''' M 011 0048

	== Information ==		== Information ==

	'''Make sure to have all Doors unlocked, otherwise this Control Module may not communicate with VCDS!'''<br>		'''Make sure to have all Doors unlocked, otherwise this Control Module may not communicate with VCDS!'''<br>

Dana: /* Information */

2015-12-22T19:02:37Z

Information

← Older revision		Revision as of 19:02, 22 December 2015
Line 5:		Line 5:
	'''Make sure to have all Doors unlocked, otherwise this Control Module may not communicate with VCDS!'''<br>		'''Make sure to have all Doors unlocked, otherwise this Control Module may not communicate with VCDS!'''<br>

	The Comfort System known from earlier Models has been integrated with the Central Electronics / Body Control Module (BCM) and is no longer available as a separate Address/Module. All related Diagnostics/Settings have to be performed via Central Electronics / Body Control Module (BCM).<br>		The Comfort System known from earlier Models has been integrated with the Central Electronics / Body Control Module (BCM) and is no longer available as a separate Address/Module. All related Diagnostics/Settings have to be performed via Address 09-Central Electronics / Body Control Module (BCM).<br>

	We have a small list of tweaks here: [[VW Golf/Golf Plus (5K/52) Tweaks\|Common Modifications & Tweaks for the VW Golf/Golf Plus (5K/52)]]<br>		We have a small list of tweaks here: [[VW Golf/Golf Plus (5K/52) Tweaks\|Common Modifications & Tweaks for the VW Golf/Golf Plus (5K/52)]]<br>
Line 11:		Line 11:

	----		----


	== Coding ==		== Coding ==

Dana at 15:59, 30 January 2015

2015-01-30T15:59:37Z

← Older revision		Revision as of 15:59, 30 January 2015
Line 28:		Line 28:

	* This Adaptation Channel is used to clear all matched Remote Controls.		* This Adaptation Channel is used to clear all matched Remote Controls.
			Note: ''If the vehicle uses a KESSY (Address; 05-Acc/Start Auth. control module) please see the Channel 001 note!''

	=== Channel 001: Remote Control Matching ===		=== Channel 001: Remote Control Matching ===
Line 34:		Line 34:
	* Start Matching new/additional Remote Controls with entering the number of new remotes (2 ''in most cases''), then '''Test''' and '''Save''' the New Value.		* Start Matching new/additional Remote Controls with entering the number of new remotes (2 ''in most cases''), then '''Test''' and '''Save''' the New Value.
	* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers should light up to confirm the Adaptation Process of each Remote Control.		* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers should light up to confirm the Adaptation Process of each Remote Control.
			Note: ''Adaptation Channel 001 may not be applicable to a BCM installed in a KESSY (Address; 05-Acc/Start Auth. control module) equipped vehicle. If Channel 001 is not available, the vehicle key, (with integrated or non-removable remote) should be automatically matched when performing [[Immobilizer#Immobilizer Generation 4 \| Immobilizer 4+]] matching. We do not have a procedure for this configuration and recommend Dealer matching if [[Official Factory Repair Information \| Immobilizer and Pass-Thru]] options are not available.''

	=== Channel 019: Factory Mode ===		=== Channel 019: Factory Mode ===

Dana: /* Replacement */

2014-08-19T15:20:23Z

Replacement

← Older revision		Revision as of 15:20, 19 August 2014
Line 44:		Line 44:

	== Replacement ==		== Replacement ==
			This Replacement procedure applies to PQ35 BCM vehicles without a KESSY (05-Acc/Start Auth.) module.
	* Make sure all vehicle remotes are present.		* Make sure all vehicle remotes are present.
	* Run and save a complete Auto-Scan and save it prior to module removal. See the [http://www.ross-tech.com/vcds/tour/autoscan.html Online Manual Auto-Scan].<br>		* Run and save a complete Auto-Scan and save it prior to module removal. See the [http://www.ross-tech.com/vcds/tour/autoscan.html Online Manual Auto-Scan].<br>
Line 55:		Line 55:
	*** Refer to this [[VW TPMS Systems without Wheel Position Recognition \| Tech Tip]] if the TPMS system does not learn the wheel sensor ID after a short drive.		*** Refer to this [[VW TPMS Systems without Wheel Position Recognition \| Tech Tip]] if the TPMS system does not learn the wheel sensor ID after a short drive.
	* Clear all fault codes and verify all comfort functions and lighting is working as per design. <br>		* Clear all fault codes and verify all comfort functions and lighting is working as per design. <br>


	== Special Notes ==		== Special Notes ==

Dana: /* Special Notes */

2014-07-24T15:31:02Z

Special Notes

← Older revision		Revision as of 15:31, 24 July 2014
Line 62:		Line 62:
	* Verify the module is not new and still in Factory Mode.		* Verify the module is not new and still in Factory Mode.
	* Check the ignition S-contact switching and driver door latch measuring block switching because remotes will not lock the doors if either are faulty/implausible.		* Check the ignition S-contact switching and driver door latch measuring block switching because remotes will not lock the doors if either are faulty/implausible.
	* Run a complete Auto-Scan to make sure other modules do not have codes which may indicate the coding is incorrect or incorrect modules are installed in the vehicle. This includes, but is not limited to, addresses 09-~~Centeral~~ Electronics/BCM and 16-Steering Wheel.		* Run a complete Auto-Scan to make sure other modules do not have codes which may indicate the coding is incorrect or incorrect modules are installed in the vehicle. This includes, but is not limited to, addresses 09-Central Electronics/BCM and 16-Steering Wheel.

	''''If the remotes will not match and the module is not confirming during the Adaptation process check the following possible causes:'''		''''If the remotes will not match and the module is not confirming during the Adaptation process check the following possible causes:'''

Dana: /* Channel 001: Remote Control Matching */

2012-08-21T00:54:35Z

Channel 001: Remote Control Matching

← Older revision		Revision as of 00:54, 21 August 2012
Line 33:		Line 33:

	* Start Matching new/additional Remote Controls with entering the number of new remotes (2 ''in most cases''), then '''Test''' and '''Save''' the New Value.		* Start Matching new/additional Remote Controls with entering the number of new remotes (2 ''in most cases''), then '''Test''' and '''Save''' the New Value.
	* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers ~~will~~ light up to confirm the Adaptation Process of each Remote Control.		* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers should light up to confirm the Adaptation Process of each Remote Control.


	=== Channel 019: Factory Mode ===		=== Channel 019: Factory Mode ===

Dana at 14:22, 24 May 2012

2012-05-24T14:22:25Z

← Older revision		Revision as of 14:22, 24 May 2012
Line 32:		Line 32:
	=== Channel 001: Remote Control Matching ===		=== Channel 001: Remote Control Matching ===

	* Start Matching new/additional Remote Controls with entering ''~~'1'~~'', then '''Test''' and '''Save''' the New Value.		* Start Matching new/additional Remote Controls with entering the number of new remotes (2 ''in most cases''), then '''Test''' and '''Save''' the New Value.
	* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.		* Press and hold the '''Unlock''' button for at least one second on each Remote Control you want to add, the Blinkers will light up to confirm the Adaptation Process of each Remote Control.

Line 56:		Line 56:
	*** Refer to this [[VW TPMS Systems without Wheel Position Recognition \| Tech Tip]] if the TPMS system does not learn the wheel sensor ID after a short drive.		*** Refer to this [[VW TPMS Systems without Wheel Position Recognition \| Tech Tip]] if the TPMS system does not learn the wheel sensor ID after a short drive.
	* Clear all fault codes and verify all comfort functions and lighting is working as per design. <br>		* Clear all fault codes and verify all comfort functions and lighting is working as per design. <br>


	''Registered customers can [mailto:Support@Ross-Tech.com contact us directly via email] for assistance. Every inquiry on this topic must include a full Auto-Scan as well as which parts have been replaced and why.''


	== Special Notes ==		== Special Notes ==

	If the remotes will not operate but are confirming while matching during the Adaptation process check the following possible causes:		'''If the remotes will not operate but are confirming while matching during the Adaptation process check the following possible causes:'''
	* Verify the module is not new and still in Factory Mode.		* Verify the module is not new and still in Factory Mode.
	* Check the ignition S-contact switching and driver door latch measuring block switching because remotes will not lock the doors if either are faulty/implausible.		* Check the ignition S-contact switching and driver door latch measuring block switching because remotes will not lock the doors if either are faulty/implausible.
	* Run a complete Auto-Scan to make sure other modules do not have codes which may indicate the coding is incorrect or incorrect modules are installed in the vehicle. This includes, but is not limited to, addresses 09-Centeral Electronics/BCM and 16-Steering Wheel.		* Run a complete Auto-Scan to make sure other modules do not have codes which may indicate the coding is incorrect or incorrect modules are installed in the vehicle. This includes, but is not limited to, addresses 09-Centeral Electronics/BCM and 16-Steering Wheel.

			''''If the remotes will not match and the module is not confirming during the Adaptation process check the following possible causes:'''
			* Incorrect Coding
			* Factory Mode enabled in new module
			* Incorrect remote(s)
			* Incorrect Central Electronics / Body Control Module (BCM)


			''Registered customers can [mailto:Support@Ross-Tech.com contact us directly via email] for assistance. Every inquiry on this topic must include a full Auto-Scan as well as which parts have been replaced and why.''

Dana at 18:39, 20 April 2012

2012-04-20T18:39:03Z

← Older revision		Revision as of 18:39, 20 April 2012
Line 58:		Line 58:


	''Registered customers can [~~http~~:~~//www.ross~~-~~tech~~.com~~/contact.html~~ contact us directly via email] for assistance. Every inquiry on this topic must include a full Auto-Scan as well as which parts have been replaced and why.''		''Registered customers can [mailto:Support@Ross-Tech.com contact us directly via email] for assistance. Every inquiry on this topic must include a full Auto-Scan as well as which parts have been replaced and why.''

Dana at 18:34, 20 April 2012

2012-04-20T18:34:31Z

← Older revision		Revision as of 18:34, 20 April 2012
Line 59:		Line 59:

	''Registered customers can [http://www.ross-tech.com/contact.html contact us directly via email] for assistance. Every inquiry on this topic must include a full Auto-Scan as well as which parts have been replaced and why.''		''Registered customers can [http://www.ross-tech.com/contact.html contact us directly via email] for assistance. Every inquiry on this topic must include a full Auto-Scan as well as which parts have been replaced and why.''


			== Special Notes ==

			If the remotes will not operate but are confirming while matching during the Adaptation process check the following possible causes:
			* Verify the module is not new and still in Factory Mode.
			* Check the ignition S-contact switching and driver door latch measuring block switching because remotes will not lock the doors if either are faulty/implausible.
			* Run a complete Auto-Scan to make sure other modules do not have codes which may indicate the coding is incorrect or incorrect modules are installed in the vehicle. This includes, but is not limited to, addresses 09-Centeral Electronics/BCM and 16-Steering Wheel.