01318: Difference between revisions
From Ross-Tech Wiki
Table Of Contents
-
1.
01318 - Control Module for Injection Pump (J399)
-
1.1.1
01318 - Control Module for Injection Pump (J399): Signal Outside Specifications
- 1.1.1.2 Possible Symptoms
- 1.1.2.2 Possible Causes
- 1.1.3.2 Possible Solutions
-
1.2.1
01318 - Control Module for Injection Pump (J399): No Communications
- 1.2.1.6 Possible Symptoms
- 1.2.2.6 Possible Causes
- 1.2.3.6 Possible Solutions
- 1.2.4.6 Special Notes
-
1.3.1
01318 - Control Module for Injection Pump (J399): No Elaboration Available
- 1.3.1.11 Possible Symptoms
- 1.3.2.11 Possible Causes
- 1.3.3.11 Special Notes
-
1.1.1
01318 - Control Module for Injection Pump (J399): Signal Outside Specifications
RtWiKiSyS0p (talk | contribs) No edit summary |
RtWiKiSyS0p (talk | contribs) No edit summary |
||
| Line 1: | Line 1: | ||
__FORCETOC__ | __FORCETOC__ | ||
== 01318 - Control Module for Injection Pump (J399) == | == 01318 - Control Module for Injection Pump (J399) == | ||
=== 01318 - Control Module for Injection Pump (J399): Signal Outside Specifications === | |||
==== Possible Symptoms ==== | |||
* Malfunction Indicator Light (MIL) ON | |||
* Limp Mode & Reduced Power/Output | |||
* Emergency/Safety Shut-Off | |||
==== Possible Causes ==== | |||
* Injection Pump (J399) faulty | |||
==== Possible Solutions ==== | |||
* Check/Replace Injection Pump (J399) | |||
=== 01318 - Control Module for Injection Pump (J399): No Communications === | === 01318 - Control Module for Injection Pump (J399): No Communications === | ||
Revision as of 21:08, 29 August 2012
01318 - Control Module for Injection Pump (J399)
01318 - Control Module for Injection Pump (J399): Signal Outside Specifications
Possible Symptoms
- Malfunction Indicator Light (MIL) ON
- Limp Mode & Reduced Power/Output
- Emergency/Safety Shut-Off
Possible Causes
- Injection Pump (J399) faulty
Possible Solutions
- Check/Replace Injection Pump (J399)
01318 - Control Module for Injection Pump (J399): No Communications
Possible Symptoms
- Malfunction Indicator Light (MIL) ON
Possible Causes
- Wiring and/or Connector(s) from/to Injection Pump (J399) faulty
- Injection Pump (J399) faulty
Possible Solutions
- Check Wiring and/or Connector(s) from/to Injection Pump (J399)
- Check Communication to Injection Pump (J399)
- See Measuring Value Block (MVB) 018
- Check/Replace Injection Pump (J399)
Special Notes
- When found on 2.5l V6 TDI, has a Compression Test been performed? This code may be stored in Combination with a Compression Test even though the Communication is OK. Under these Circumstances this Fault Code should be cleared.
01318 - Control Module for Injection Pump (J399): No Elaboration Available
Possible Symptoms
- Malfunction Indicator Light (MIL) ON
Possible Causes
- Control Module Software Issue
Special Notes
- When found on 2.5l V6 TDI, contact Ross-Tech for Assistance.