Immobilizer IV Immobilizer Swapping (Instrument Cluster): Difference between revisions

From Ross-Tech Wiki
Newer edit →
mNo edit summary
 
No edit summary
Line 24: Line 24:
'''[Done, Go Back]'''<br>
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back - 06]'''<br>
'''[Close Controller, Go Back - 06]'''<br>
== Instrument Cluster Swapping (Used Cluster) ==
'''<u>Prerequisites:</u>'''<br>
* The new (used) cluster is installed in the car.
* You do have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.
* Battery voltage at least 12.0 V.<br>
'''[Select]'''<br>
'''[25 - Immobilizer]'''<br>
'''[Security Access - 16]'''<br>
''For the following procedure, '''use the PIN of the NEW (USED)''' instrument cluster.''<br>
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>
* '''4-digit PIN'''
** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
* '''7-digit PIN'''
** '''[Use 7-digit PIN/SKC]'''
** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
** '''[OK]'''
** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
'''[Do it!]'''<br>
'''[Adaptation - 10]'''<br>
Enter 050 in "Channel Number".<br>
'''[Read]'''<br>
''For the following procedure, '''use the PIN of the OLD (ORIGINAL)''' instrument cluster.''<br>
''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''<br>
* '''4-digit PIN'''
** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
* '''7-digit PIN'''
** '''[Use 7-digit PIN/SKC]'''
** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
** '''[OK]'''
** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
'''[Save]'''<br>
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back - 06]'''<br>
* Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
* Verify that the NEW (USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now.

Revision as of 13:03, 1 June 2006

This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer IV.

Determining IMMO-ID & VIN (ECU)

[Select]
[01 - Engine]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Determining IMMO-ID & VIN (Instrument Cluster)

[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]


Instrument Cluster Swapping (Used Cluster)

Prerequisites:

  • The new (used) cluster is installed in the car.
  • You do have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.
  • Battery voltage at least 12.0 V.


[Select]
[25 - Immobilizer]


[Security Access - 16]
For the following procedure, use the PIN of the NEW (USED) instrument cluster.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.

  • 4-digit PIN
    • Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
  • 7-digit PIN
    • [Use 7-digit PIN/SKC]
    • Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
    • [OK]
    • VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".

[Do it!]


[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the OLD (ORIGINAL) instrument cluster.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.

  • 4-digit PIN
    • Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
  • 7-digit PIN
    • [Use 7-digit PIN/SKC]
    • Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
    • [OK]
    • VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".

[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]


  • Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
  • Verify that the NEW (USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now.
Retrieved from "https://wiki.ross-tech.com/wiki/index.php?title=Immobilizer_IV_Immobilizer_Swapping_(Instrument_Cluster)&oldid=2233"
Contact Privacy Accessibility