VW Golf VII (5G/AU)
Table Of Contents
- 1. [01] - Engine
- 2. [02] - Auto Trans
- 3. [03] - ABS Brakes
- 4. [05] - Access/Start Authorization
- 5. [08] - Auto HVAC
- 6. [09] - Cent. Elect.
- 7. [15] - Airbags
- 8. [16] - Steering Wheel
- 9. [17] - Instrument Cluster
- 10. [19] - CAN Gateway
- 11. [2B] - Steering Column Lock
- 12. [42] - Door Elect, Driver
- 13. [44] - Steering Assist
-
14.
Basic Setting
- 14.1.14 Sensor for Steering Angle (G85)
-
15.
Video Link
- 15.1.16 [52] - Door Elect, Pass
- 15.2.16 [55] - Headlight Aim Control
- 15.3.16 [5F] - Information Electronics
- 15.4.16 [75] - Telematics
- 15.5.16 [A9] - Struct. Borne Sound
This page will have information about the Golf 7.
These pages have some information on tweaks for the Mk7 Golf platform vehicles:
http://forums.ross-tech.com/showthread.php?512-MQB-Platform-tweaks
http://www.golfgtiforum.co.uk/index.php?topic=260248.0
http://vcds.greg-roberts.com/view-entries
http://forums.vwvortex.com/showthread.php?7013354
http://forums.vwvortex.com/showthread.php?7231270
https://sites.google.com/a/naturalnetworks.ca/vw-golf-mk7-vcds-how-to/
http://forums.vwvortex.com/showthread.php?8687226-VCDS-coding-on-an-Alltrack
| Volkswagen Golf VII | |
|---|---|
| |
| Source: Ross-Tech, LLC | |
| Information | |
| Manufacturer: | Volkswagen AG |
| Chassis Code: | 5G / AU |
| Platform: | VW37X |
| Model Years: | from 2013 |
| Model Years (US): | from 2015 |
| Predecessor: | VW Golf/Golf Plus (5K/52) |
| Successor: | - |
| Interface Hardware | |
| All model years HEX-V2, HEX-NET | |
| DLC Location | |
| |
|
The DLC is located in the Driver Footwell. | |
[01] - Engine
[02] - Auto Trans
- Replacement of the transmission or mechatronics unit will result in P1701
[03] - ABS Brakes
- Basic Setting
- 5Q0-907-379-IPB-V1.clb
- EV_Brake1UDSContiMK100IPB_VW37
- G85 is calibrated in Address 44. See this post
[05] - Access/Start Authorization
[08] - Auto HVAC
[09] - Cent. Elect.
Note #1: Before making ANY changes, you should run and Save a controller channel map of Adaptation in address 09. Control_Module_Maps
Note #2: Starting around model year 2018 many BCM/CECM modules show all zeros for Coding. In these applications, Coding is neither necessary nor possible. Instead changes are made using Adaptation as discussed here: https://forums.ross-tech.com/index.php?threads/10616/
Note #3: In some of the latest models, you need to open the hood to make changes due to the Diagnostic Firewall that is discussed here:
https://forums.ross-tech.com/index.php?threads/15536/
[15] - Airbags
[16] - Steering Wheel
[17] - Instrument Cluster
[19] - CAN Gateway
[2B] - Steering Column Lock
[42] - Door Elect, Driver
[44] - Steering Assist
Basic Setting
Sensor for Steering Angle (G85)
Prerequisites:
- Start the vehicle.
[44-Steering Assist]
[Security Access - 16]
- Enter 19249
[Basic Settings - 04]
- [MAS00815] Steering angle sensor
[Go!]
- Rotate steering wheel all the way to the left, hold firmly against end stop for 5 seconds.
- Rotate steering wheel all the way to the right, hold firmly against end stop for 5 seconds.
- Center steering wheel, front wheel straight ahead.
[Stop]
- Several error messages and warnings will appear on the cluster, what messages you get can vary based on how the vehicles is equipped.
[Done, Go Back]
- Rotate steering wheel all the way to the left, hold firmly against end stop for 5 seconds.
- Rotate steering wheel all the way to the right, hold firmly against end stop for 5 seconds.
- Center steering wheel, front wheel straight ahead.
[Close Controller, Go Back - 06]
- Cycle the ignition off for 10 seconds.
Notes
- When doing the Basic Settings, should see the message of "Running", but it may not change to "Finished Correctly"
- Several control modules will flag DTCs, "Databus" type codes that can cleared out after the 10 second ignition cycle.
Video Link
https://www.youtube.com/watch?v=bXScTl4VvMc
[52] - Door Elect, Pass
[55] - Headlight Aim Control
[5F] - Information Electronics
[75] - Telematics
[A9] - Struct. Borne Sound
No categories.