Bentley Continental (3W) Parking Brake

From Ross-Tech Wiki

Jump to: navigation, search


Contents

Coding

  • 0022401 = Bentley Continental GT (3W3/BY614) North American Region (NAR)
  • 0022413 = Bentley Continental GT (3W3/BY614) Rest of World (RoW)
  • 0032401 = Bentley Continental Flying Spur (3W2/BY611) North American Region (NAR)
  • 0032413 = Bentley Continental Flying Spur (3W2/BY611) Rest of World (RoW)


Basic Setting

Caution!

  • Do not perform any of these Basic Settings while the brakes are disassembled! Opening, closing, function tests, and otherwise cycling the Electronic Parking brakes should only be done with the pads and calipers properly installed on the rotors.
  • Please follow the procedures EXACTLY. There's a reason for every step. If you skip any prerequisites or other steps here, you are likely to experience "issues" for which no documented resolutions exist, in which case we will not be able to help you resolve them.
  • It is strongly recommended to run a full Auto-Scan first thing to check for any preexisting faults! There have been several reports of repair shops damaging the Electronic Parking Brake System when trying to do rear brakes, but not telling the customer and then sending the car out the door.

Open Rear Parking Brake

Prerequisites:

  • Connect a battery charger as per repair manual.
    • See the Battery Locations Here if the repair manual information is limited.
  • Cycle the Parking Brake ON, then OFF first.

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 007
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now opening.
[Done, Go Back]
[Close Controller, Go Back - 06]

  • Turn ignition off.


The caliper pistons do not move back into the caliper, this is normal.

Close Rear Parking Brake

Prerequisites:

  • Connect a battery charger.

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 006
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now closing.
[Done, Go Back]
[Close Controller, Go Back - 06]


Function Test

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 010
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The brake pads are now opening and closing 3 times.
[Done, Go Back]
[Close Controller, Go Back - 06]


Inclination Sensor Calibration

[Select]
[53 - Parking Brake]
[Basic Settings - 04]
Group 020
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
The Inclination Sensor will then be calibrated.
[Done, Go Back]
[Close Controller, Go Back - 06]

Replacement

When Replacing the Electronic Parking Brake Control Module (J540), there are additional steps that need to be performed. Before the actual Control Module Coding can take place, some calibrations must be performed:

  • Calibrate Electronic Parking Brake Switch (F42)
    • Press Electronic Parking Brake Switch down
    • Pull Electronic Parking Brake Switch up
    • Push and hold Brake Pedal, then press Electronic Parking Brake Switch down.
    • Parking Brake should NOT be engaged now.
  • Perform Inclination Sensor Calibration (see Details above)
  • Perform Function Test/Assembly Check (see Details above)
  • Code Control Module (see Details above)


Video Link

Electro-Mechanical Parking Brake (EPB): Rear Brake Service

Image4.jpg

https://www.youtube.com/watch?v=zFZJj39FZ3s




Unless otherwise noted, all content on this site is Copyright © 2000-2010 by Ross-Tech LLC. All rights reserved.
"VCDS" is a Registered Trademark of Ross-Tech, LLC.
Ross-Tech is not affiliated with the Volkswagen Group in any way.