User:Dana

From Ross-Tech Wiki

This is my test page please leave it alone ;-)


_


Gasoline

_



A0A0A0

  1. C0C0C0

D0D0D0 FFFFFF

  • File:File.png
    alt text
    to use a 200 pixel wide rendition in a box in the left margin with 'alt text' as description
  • Media:File.ogg for directly linking to the file without displaying the file




This chart shows what information is needed to perform each procedure. The requirements and steps differ depending on whether the component you are installing is brand new, or if it has been previously matched to a vehicle. Used keys are ones that have previously been matched to a different vehicle.




space Immo 1 & 2 Immo 3 Immo 4A Immo 4C
Key Matching (New)
Vehicle SKC
Needed
Vehicle SKC
Needed
Vehicle SKC
Needed
Key Matching (Used)
Vehicle SKC
Needed
Not Possible Not Possible Not Possible
ECU Swapping (New)
No SKC needed
see note
Vehicle SKC Needed Vehicle SKC Needed -
ECU Swapping (Used) No SKC needed
see note
- - -
Cluster Swapping (New) - - - -
Cluster Swapping (Used) - - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -



This is
a table


An example table
First header Second header
upper left   right side
lower left lower middle
A table in a table
[[1]] File:Wiki.png

Two Wikimedia logos


http://meta.wikimedia.org/wiki/Help:Table




0xxxxxxx 0 1 0 1 0 1 0 1
x0xxxxxx 0 1 0 1 0 1 0 1
xx0xxxxx 0 1 0 1 0 1 0 1
xxx0xxxx 0 1 0 1 0 1 0 1
xxxx0xxx 0 1 0 1 0 1 0 1
xxxxx0xx 0 1 0 1 0 1 0 1
xxxxxx0x 0 1 0 1 0 1 0 1
xxxxxxx0 0 1 0 1 0 1 0 1

Measuring Block Group 066
Field 2 Data
0xxxxxxx 0 1 0 1 0 1 0 1 0 = 1 =
x0xxxxxx - 0 = 1 =
xx0xxxxx 0 = 1 =
xxx0xxxx 0 = 1 =
xxxx0xxx 0 = 1 =
xxxxx0xx 0 = 1 =
xxxxxx0x 0 = 1 =
xxxxxxx0 0 = Normal CCS 1 = Accel. pedal
overide


Measuring Block Group 066
Field 4 Data
0xxxxxxx 0 1 0 1 0 1 0 1
x0xxxxxx
xx0xxxxx
xxx0xxxx
xxxx0xxx
xxxxx0xx 0 = 1 =
xxxxxx0x 0 = 1 =
xxxxxxx0 0 = Normal CCS 1 = Accel. pedal
overide


0 1 0 1 1 1 0 1 0 = Brake Not Depressed 1 = Brake depressed (brake light switch)
0 = Brake Not Depressed 1 = Brake depressed (brake pedal switch)
0 = Clutch Not Depressed 1 = Clutch Depressed (always 1 in Auto. Trans.)
0 = CCS Not active in ECM 1 = CCS active in ECM
N/A N/A
N/A N/A
0 = Accel. pedal overide 1 = CCS Operating
0 = Normal CCS 1 = Accel. pedal overide




Reading Roof Electronics Switch Conditions, Electric Power Top

Measuring Block Group 001
Field 2 X Field 3 Data
1 1 0 1 1 0 1 0 1 0 X 0 1 1 0 F201
F290
F293
F200
X
Not used, always "0"
F292
X
F171
F202
F294
F295
F172
Switch Point for Bow UP
Switch Point for Bow OPEN
Switch Point for Bow DEAD CENTER





Coding

  • 0655360 = Sunroof (Sliding & Tilting)
  • 0655361 = Sunroof (Tilting only)
  • 0655362 = Parking Aid & Sunroof (Sliding & Tilting)
  • 0655363 = Parking Aid & Sunroof (Tilting only)



Roof Data

Roof Binary Data in Closed Position

Measuring Block Group 002
1 1 1 1 0 1 1 0 0 1 1 0 1 Data
G672
G567
G559
G558
G566
G565
G564
G563
G562
G561
G560
G557
G556


Roof Binary Data as Top Cycles Open

click thumbnail to enlarge photo
Eos01.jpg
1
Eos02.jpg
2
Eos03.jpg
3
Eos04.jpg
4
Eos05.jpg
5
Eos06.jpg
6
Eos07.jpg
7
Eos08.jpg
8
Eos09.jpg
9
Eos10.jpg
10
Eos11.jpg
11


Roof Binary Data in Open Position

Measuring Block Group 002
0 0 0 0 1 1 1 1 0 0 0 0 1


Special Notes

  • The G672 (13th BIT) is only on 2009 and later models, older version will only have 12 BITs of data.


Video Link

Eos Top screengrab.jpg

http://www.youtube.com/watch?v=3owlG0ICF_s




17968/P1560/005472 - Engine Speed Sensor (G28): No Signal

Possible Causes

  • Engine Speed too fast
  • Stuck throttle

Possible Solutions

  • Clear Fault Codes
  • Remove Lead from Foot

Special Notes

  • This DTC indicates that the Engine Speed has passed the recommended safe RPM limit, which may potentially cause severe engine damage.

This category lists Fault Codes or Diagnostic Trouble Codes (DTC's),
which are yet documented with possible symptoms, causes, and solutions.
Additional codes are being continuously added.