View source for Audi TT (8N) Brake Electronics (MK60)

__FORCETOC__

== Coding ==
=== ABS/EDS/ASR/ESP (Front-Wheel-Drive) ===
=== ABS/EDS/ASR/ESP (All-Wheel-Drive) ===


== Basic Setting ==
=== Sensor for Steering Angle (G85) ===

'''<u>Prerequisites:</u>'''<br>
* Start the vehicle.
* Turn the steering wheel one turn to the right and one turn to the left.
* Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
* If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
* Ensure that the steering wheel is not moved again.
* Keep the engine running and do not switch off the ignition.
* System voltage at least 12.0 V.<br><br>

'''[Select]'''<br>
'''[03 - Brake Electronics]'''<br>
'''[Coding-II - 11]'''<br>
Enter 40168, to enable the basic setting.<br>
'''[Do it!]'''<br>
'''[Basic Settings - 04]'''<br>
Group 060<br>
'''[Go!]'''<br>
Activate the Basic Setting.<br>
'''[ON/OFF/Next]'''<br>
After a successful basic setting, field 2 should say "OK".<br>
'''[Done, Go Back]'''<br>
To make sure the basic setting was succesful, check the sensor again.<br>
'''[Measuring Blocks - 08]'''<br>
Group 004<br>
'''[Go!]'''<br>
Check field 1, the value has to be between -4.5 and +4.5 °.<br>
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back - 06]'''<br>


=== Lateral Acceleration Sensor (G200) ===

'''<u>Prerequisites:</u>'''<br>
* System voltage at least 12.0 V.<br><br>

'''[Select]'''<br>
'''[03 - Brake Electronics]'''<br>
'''[Measuring Blocks - 08]'''<br>
Group 004<br>
'''[Go!]'''<br>
Check field 2, the value has to be between -1.5 and +1.5 m/s².<br>
'''[Done, Go Back]'''<br>
'''[Coding-II - 11]'''<br>
Enter 40168, to enable the basic setting.<br>
'''[Do it!]'''<br>
'''[Basic Settings - 04]'''<br>
Group 063<br>
'''[Go!]'''<br>
Activate the Basic Setting.<br>
'''[ON/OFF/Next]'''<br>
After a successful basic setting, field 2 should say "OK".<br>
'''[Done, Go Back]'''<br>
To make sure the basic setting was succesful, check the sensor again.<br>
'''[Measuring Blocks - 08]'''<br>
Group 004<br>
'''[Go!]'''<br>
Check field 2, the value has to be between -1.5 and +1.5 m/s².<br>
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back - 06]'''<br>


=== Brake Pressure Sensor 1 (G201) ===

'''<u>Prerequisites:</u>'''<br>
* System voltage at least 12.0 V.<br><br>

'''[Select]'''<br>
'''[03 - Brake Electronics]'''<br>
'''[Coding-II - 11]'''<br>
Enter 40168, to enable the basic setting.<br>
'''[Do it!]'''<br>
'''[Basic Settings - 04]'''<br>
Group 066<br>
'''[Go!]'''<br>
Activate the Basic Setting.<br>
'''[ON/OFF/Next]'''<br>
After a successful basic setting, field 2 should say "OK".<br>
'''[Done, Go Back]'''<br>
To make sure the basic setting was succesful, check the sensor again.<br>
'''[Measuring Blocks - 08]'''<br>
Group 005<br>
'''[Go!]'''<br>
Check field 1, the value has to be between -7.0 and +7.0 bar.<br>
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back - 06]'''<br>


=== Longitudinal Acceleration Sensor (G251) ===

'''<u>Prerequisites:</u>'''<br>
* System voltage at least 12.0 V.<br> 
* Measuring Value Block Group 006, Field 1 is between (-1.5) and (+1.5) m/s²<br><br>

'''[Select]'''<br>
'''[03 - Brake Electronics]'''<br>
'''[Coding-II - 11]'''<br>
Enter 40168, to enable the basic setting.<br>
'''[Do it!]'''<br>
'''[Basic Settings - 04]'''<br>
Group 069<br>
'''[Go!]'''<br>
Activate the Basic Setting.<br>
'''[ON/OFF/Next]'''<br>
After a successful basic setting, field 2 should say "OK".<br>
'''[Done, Go Back]'''<br>
To make sure the basic setting was successful, check the sensor again.<br>
'''[Measuring Blocks - 08]'''<br>
Group 006<br>
'''[Go!]'''<br>
Re-Check field 1, the value has to be between -1.5 and +1.5 m/s².<br>
'''[Done, Go Back]'''<br>
'''[Close Controller, Go Back - 06]'''<br>

== Special Procedures ==

=== System Function Test ===

See [[ESP System Function Test (Conti/Teves)|System Function Test]]