Difference between revisions of "Audi A4 (8E) Brake Electronics (Bosch 5.7)"
| Line 1: | Line 1: | ||
__FORCETOC__ | __FORCETOC__ | ||
| − | All of the following procedures must be performed in order, | + | All of the following procedures must be performed in order, '''WITHOUT''' shutting off the ignition or exiting out of the ABS controller. |
== Login == | == Login == | ||
| Line 56: | Line 56: | ||
=== Steering Angle Sensor (G85) Calibration === | === Steering Angle Sensor (G85) Calibration === | ||
| − | ''' | + | '''''Note''': ''Make sure the above Login and Coding have been done successfully before proceeding.''<br> |
| − | ''' | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
'''[Meas. Blocks - 08]'''<br> | '''[Meas. Blocks - 08]'''<br> | ||
Group 005 Field 1 (Steering Angle Sensor -G85-)<br> | Group 005 Field 1 (Steering Angle Sensor -G85-)<br> | ||
| + | Turn steering wheel at least 30 ° left and back straight ahead.<br> | ||
Specification: 0.0 °<br> | Specification: 0.0 °<br> | ||
Tolerance (when straight): ±5.0 °<br> | Tolerance (when straight): ±5.0 °<br> | ||
Revision as of 12:56, 18 May 2010
All of the following procedures must be performed in order, WITHOUT shutting off the ignition or exiting out of the ABS controller.
Login
Note #1: After Login has been carried out you need to recode the control module.
Note #2: Special Login 09399 is used for BFB Engine with 1LT Brakes and Multitronic.
Note #3: The PR codes ( such as 1LJ ) can be found in a sticker near the spare tire well. Click this link to see an example of a sticker 
- 0?xxx: Chassis
- 9 = Audi A4
- 0x?xx: Brakes
- 2 = Brembo 17" (PR-1LJ)
- 3 = FN3 16" (PR-1LT/1LF)
- 4 = HP2 16" (PR-1LX)
- 4 = FNR 16" (PR-1LA/1LG)
- 5 = FN3 15" (PR-1LB/1LE)
- 6 = C54 (PR-1LZ)
- 0xx?x: Engine
- 5 = 4/6 Cyl. Diesel
- 7 = 4/5 Cyl. Gasoline
- 9 = 6/8 Cyl. Gasoline
- 0xxx?: Transmission
- 5 = Manual
- 7 = Automatic (5HP19, 5HP24, AG4, AG5)
- 9 = Multitronic (01J, CVT)
Coding
Note #1: Coding is accepted after a specific login has been carried out.
Note #2: After successful coding the steering angle sensor basic setting needs to be carried out.
Note #3: Special Coding 04499 is used for BFB Engine with 1LT Brakes and Multitronic.
Note #4: The PR codes ( such as 1LJ ) can be found in a sticker near the spare tire well. Click this link to see an example of a sticker
- 0?xxx: Chassis
- 4 = Audi A4
- 0x?xx: Brakes
- 1 = C54 (PR-1LZ)
- 2 = FN3 15" (PR-1LB/1LE)
- 3 = HP2 16" (PR-1LX)
- 3 = FNR 16" (PR-1LG)
- 4 = FN3 16" (PR-1LT/1LF)
- 5 = Brembo 17" (PR-1LJ)
- 0xx?x: Engine
- 5 = 4/6 Cyl. Diesel
- 7 = 4/5 Cyl. Gasoline
- 9 = 6/8 Cyl. Gasoline
- 0xxx?: Transmission
- 5 = Manual
- 7 = Automatic (5HP19, 5HP24, AG4, AG5)
- 9 = Multitronic (01J, CVT)
Basic Setting
Steering Angle Sensor (G85) Calibration
Note: Make sure the above Login and Coding have been done successfully before proceeding.
[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Turn steering wheel at least 30 ° left and back straight ahead.
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]
[Login - 11]
Enter 40168
[Do It!]
[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]
[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]
[Close Controller, Go Back - 06]