Difference between revisions of "Audi A4 (8E) Brake Electronics (Bosch 5.7)"
| Line 40: | Line 40: | ||
**2 = FN3 15" (PR-1LB/1LE) | **2 = FN3 15" (PR-1LB/1LE) | ||
**3 = HP2 16" (PR-1LX) | **3 = HP2 16" (PR-1LX) | ||
| − | **3 = FNR 16" (PR-1LG) | + | **3 = FNR 16" (PR-1LA/1LG) |
**4 = FN3 16" (PR-1LT/1LF) | **4 = FN3 16" (PR-1LT/1LF) | ||
**5 = Brembo 17" (PR-1LJ) | **5 = Brembo 17" (PR-1LJ) | ||
Revision as of 16:02, 20 April 2011
All of the following procedures must be performed in order, WITHOUT shutting off the ignition or exiting out of the ABS controller.
Login
Note #1: After Login has been carried out you need to recode the control module.
Note #2: Special Login 07499 is used for 6-Cylinder Diesel Engine with 1LG Brakes and Multitronic.
Note #3: The Production Codes (PR-Code) such as 1LX can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual. Click here to see an Example of a Sticker.
- 0?xxx: Chassis
- 9 = Audi A4
- 0x?xx: Brakes
- 2 = Brembo 17" (PR-1LJ)
- 3 = FN3 16" (PR-1LT/1LF)
- 4 = HP2 16" (PR-1LX)
- 4 = FNR 16" (PR-1LA/1LG)
- 5 = FN3 15" (PR-1LB/1LE)
- 6 = C54 (PR-1LZ)
- 0xx?x: Engine
- 5 = 4/6 Cyl. Diesel
- 7 = 4/5 Cyl. Gasoline
- 9 = 6/8 Cyl. Gasoline
- 0xxx?: Transmission
- 5 = Manual
- 7 = Automatic (5HP19, 5HP24, AG4, AG5)
- 9 = Multitronic (01J, CVT)
Coding
Note #1: Coding is accepted after a specific login has been carried out.
Note #2: After successful coding the steering angle sensor basic setting needs to be carried out.
Note #3: Special Coding 04499 is used for BFB Engine with 1LT Brakes and Multitronic.
Note #4: The Production Codes (PR-Code) such as 1LX can be found on a Sticker near the Spare Tire Well and/or the 1st Page of the Service Manual. Click here to see an Example of a Sticker.
- 0?xxx: Chassis
- 4 = Audi A4
- 0x?xx: Brakes
- 1 = C54 (PR-1LZ)
- 2 = FN3 15" (PR-1LB/1LE)
- 3 = HP2 16" (PR-1LX)
- 3 = FNR 16" (PR-1LA/1LG)
- 4 = FN3 16" (PR-1LT/1LF)
- 5 = Brembo 17" (PR-1LJ)
- 0xx?x: Engine
- 5 = 4/6 Cyl. Diesel
- 7 = 4/5 Cyl. Gasoline
- 9 = 6/8 Cyl. Gasoline
- 0xxx?: Transmission
- 5 = Manual
- 7 = Automatic (5HP19, 5HP24, AG4, AG5)
- 9 = Multitronic (01J, CVT)
Basic Setting
Steering Angle Sensor (G85) Calibration
Before starting the procedure turn the steering wheel at least 30 ° left and back straight ahead.
[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]
[Login - 11]
Enter 40168
[Do It!]
[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]
[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]