Difference between revisions of "P106B/004203"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) (New page: __FORCETOC__ == P106B/004203 - Throttle Valve: Stuck or difficult to move == ==== Possible Symptoms ==== * Malfunction Indicator Lamp (MIL) active ==== Possible Causes ==== * Wiring/Co...) |
RtWiKiSyS0p (talk | contribs) m |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 20: | Line 20: | ||
==== Special Notes ==== | ==== Special Notes ==== | ||
| − | * When found on 4.2l CR-TDI (BVN), the Learning Values have to be cleared after replacing the Throttle Body Control Module. '''DO NOT CLEAR LEARNED VALUES IF YOU HAVE NOT REPLACED THE THROTTLE BODY CONTROL MODULE!''' Otherwise the proper values are being cleared and incorrect values are being learned. | + | * When found on 3.0l CR-TDI (i.e. BKS/BUG) or 4.2l CR-TDI (BVN), the Learning Values have to be cleared after replacing the Throttle Body Control Module. |
| + | **'''DO NOT CLEAR LEARNED VALUES IF YOU HAVE NOT REPLACED THE THROTTLE BODY CONTROL MODULE!''' Otherwise the proper values are being cleared and incorrect values are being learned. | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
| − | '''[01 - Engine]''' (for Bank 1/J388) or '''11 - Engine 2''' (for Bank 2/J544)<br> | + | '''[01 - Engine]''' (for Bank 1/J388) or '''[11 - Engine 2]''' (for Bank 2/J544)<br> |
'''[Coding-II - 11]'''<br> | '''[Coding-II - 11]'''<br> | ||
| Line 29: | Line 30: | ||
'''[Do It!]'''<br> | '''[Do It!]'''<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
| − | '''[Close Controller, Go Back - 06]''' | + | '''[Close Controller, Go Back - 06]'''<br> |
* Switch the Ignition OFF. | * Switch the Ignition OFF. | ||
* Switch the Ignition ON for 1 Second, then turn it OFF immediately. | * Switch the Ignition ON for 1 Second, then turn it OFF immediately. | ||
Latest revision as of 10:43, 30 March 2012
P106B/004203 - Throttle Valve: Stuck or difficult to move
Possible Symptoms
- Malfunction Indicator Lamp (MIL) active
Possible Causes
- Wiring/Connectors from/to Throttle Body Control Module to Engine Control Module faulty
- Throttle Body Control Module Damaged and/or Moving Difficulties
Possible Solutions
- Check Wiring/Connectors from/to Throttle Body Control Module to Engine Control Module
- Check for properly attached Connectors, twisted Pins, loose Contact, Corrosion and Water Ingress
- Check Throttle Body Control Module for Damage and Moving Difficulties
- Perform (Selective) Output Test
Special Notes
- When found on 3.0l CR-TDI (i.e. BKS/BUG) or 4.2l CR-TDI (BVN), the Learning Values have to be cleared after replacing the Throttle Body Control Module.
- DO NOT CLEAR LEARNED VALUES IF YOU HAVE NOT REPLACED THE THROTTLE BODY CONTROL MODULE! Otherwise the proper values are being cleared and incorrect values are being learned.
[Select]
[01 - Engine] (for Bank 1/J388) or [11 - Engine 2] (for Bank 2/J544)
[Coding-II - 11]
- Enable the Learning Procedure by Entering 10021.
[Do It!]
[Done, Go Back]
[Close Controller, Go Back - 06]
- Switch the Ignition OFF.
- Switch the Ignition ON for 1 Second, then turn it OFF immediately.
- Wait at least 30 Seconds, then switch the Ignition ON again.
- Now Check if all remaining fault codes can be cleared.