Difference between revisions of "00515"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) m |
RtWiKiSyS0p (talk | contribs) |
||
| Line 18: | Line 18: | ||
* Some older engines store this code as long as the engine is not running, if in doubt read fault codes with the engine running again. | * Some older engines store this code as long as the engine is not running, if in doubt read fault codes with the engine running again. | ||
| + | |||
| + | |||
| + | === 00515 - Camshaft Position (Hall) Sensor (G40): Implausible Signal === | ||
| + | |||
| + | ==== Possible Causes ==== | ||
| + | |||
| + | * Camshaft Timing Out of Specification | ||
| + | * Wiring to Camshaft Position (Hall) Sensor (G40) faulty | ||
| + | * Camshaft Position (Hall) Sensor (G40) faulty | ||
| + | * Engine Control Module faulty | ||
| + | |||
| + | ==== Possible Solutions ==== | ||
| + | |||
| + | * Check Camshaft Timing | ||
| + | * Check Wiring to Camshaft Position (Hall) Sensor (G40) | ||
| + | * Check/Replace Camshaft Position (Hall) Sensor (G40) | ||
| + | * Check/Replace Engine Control Module | ||
Latest revision as of 10:05, 15 November 2007
00515 - Camshaft Position (Hall) Sensor (G40)
00515 - Camshaft Position (Hall) Sensor (G40): No Signal
Possible Causes
- Wiring to Camshaft Position (Hall) Sensor (G40) faulty
- Camshaft Position (Hall) Sensor (G40) faulty
Possible Solutions
- Check Wiring to Camshaft Position (Hall) Sensor (G40)
- Check/Replace Camshaft Position (Hall) Sensor (G40)
- Check/Replace Engine Control Module
Special Notes
- Some older engines store this code as long as the engine is not running, if in doubt read fault codes with the engine running again.
00515 - Camshaft Position (Hall) Sensor (G40): Implausible Signal
Possible Causes
- Camshaft Timing Out of Specification
- Wiring to Camshaft Position (Hall) Sensor (G40) faulty
- Camshaft Position (Hall) Sensor (G40) faulty
- Engine Control Module faulty
Possible Solutions
- Check Camshaft Timing
- Check Wiring to Camshaft Position (Hall) Sensor (G40)
- Check/Replace Camshaft Position (Hall) Sensor (G40)
- Check/Replace Engine Control Module
00515 - Camshaft Position (Hall) Sensor (G40): Open or Short to Plus
Possible Causes
- Wiring to Camshaft Position (Hall) Sensor (G40) faulty
- Camshaft Position (Hall) Sensor (G40) Installation faulty
- Camshaft Timing Out of Specification
- Camshaft Position (Hall) Sensor (G40) faulty
Possible Solutions
- Check Wiring to Camshaft Position (Hall) Sensor (G40)
- Check/Replace Camshaft Position (Hall) Sensor (G40)
- Check Camshaft Timing
- Check/Replace Engine Control Module
00515 - Camshaft Position (Hall) Sensor (G40): Short to Ground
Possible Symptoms
- Power Loss
- Emissions not OK
- High Fuel Consumption
Possible Causes
- Wiring to Camshaft Position (Hall) Sensor (G40) faulty
- Camshaft Position (Hall) Sensor (G40) faulty
Possible Solutions
- Check Wiring to Camshaft Position (Hall) Sensor (G40)
- Check/Replace Camshaft Position (Hall) Sensor (G40)