Difference between revisions of "P106B/004203"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) m |
RtWiKiSyS0p (talk | contribs) m |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 20: | Line 20: | ||
==== Special Notes ==== | ==== Special Notes ==== | ||
| − | * When found on 4.2l CR-TDI (BVN), the Learning Values have to be cleared after replacing the Throttle Body Control Module. | + | * When found on 3.0l CR-TDI (i.e. BKS/BUG) or 4.2l CR-TDI (BVN), the Learning Values have to be cleared after replacing the Throttle Body Control Module. |
**'''DO NOT CLEAR LEARNED VALUES IF YOU HAVE NOT REPLACED THE THROTTLE BODY CONTROL MODULE!''' Otherwise the proper values are being cleared and incorrect values are being learned. | **'''DO NOT CLEAR LEARNED VALUES IF YOU HAVE NOT REPLACED THE THROTTLE BODY CONTROL MODULE!''' Otherwise the proper values are being cleared and incorrect values are being learned. | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
| − | '''[01 - Engine]''' (for Bank 1/J388) or '''11 - Engine 2''' (for Bank 2/J544)<br> | + | '''[01 - Engine]''' (for Bank 1/J388) or '''[11 - Engine 2]''' (for Bank 2/J544)<br> |
'''[Coding-II - 11]'''<br> | '''[Coding-II - 11]'''<br> | ||
| Line 30: | Line 30: | ||
'''[Do It!]'''<br> | '''[Do It!]'''<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
| − | '''[Close Controller, Go Back - 06]''' | + | '''[Close Controller, Go Back - 06]'''<br> |
* Switch the Ignition OFF. | * Switch the Ignition OFF. | ||
* Switch the Ignition ON for 1 Second, then turn it OFF immediately. | * Switch the Ignition ON for 1 Second, then turn it OFF immediately. | ||
Latest revision as of 10:43, 30 March 2012
P106B/004203 - Throttle Valve: Stuck or difficult to move
Possible Symptoms
- Malfunction Indicator Lamp (MIL) active
Possible Causes
- Wiring/Connectors from/to Throttle Body Control Module to Engine Control Module faulty
- Throttle Body Control Module Damaged and/or Moving Difficulties
Possible Solutions
- Check Wiring/Connectors from/to Throttle Body Control Module to Engine Control Module
- Check for properly attached Connectors, twisted Pins, loose Contact, Corrosion and Water Ingress
- Check Throttle Body Control Module for Damage and Moving Difficulties
- Perform (Selective) Output Test
Special Notes
- When found on 3.0l CR-TDI (i.e. BKS/BUG) or 4.2l CR-TDI (BVN), the Learning Values have to be cleared after replacing the Throttle Body Control Module.
- DO NOT CLEAR LEARNED VALUES IF YOU HAVE NOT REPLACED THE THROTTLE BODY CONTROL MODULE! Otherwise the proper values are being cleared and incorrect values are being learned.
[Select]
[01 - Engine] (for Bank 1/J388) or [11 - Engine 2] (for Bank 2/J544)
[Coding-II - 11]
- Enable the Learning Procedure by Entering 10021.
[Do It!]
[Done, Go Back]
[Close Controller, Go Back - 06]
- Switch the Ignition OFF.
- Switch the Ignition ON for 1 Second, then turn it OFF immediately.
- Wait at least 30 Seconds, then switch the Ignition ON again.
- Now Check if all remaining fault codes can be cleared.