Difference between revisions of "02432"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) m |
RtWiKiSyS0p (talk | contribs) |
||
| (One intermediate revision by one other user not shown) | |||
| Line 1: | Line 1: | ||
| − | |||
== 02432 - Supply Voltage for Left Parking Brake Motor (V282) == | == 02432 - Supply Voltage for Left Parking Brake Motor (V282) == | ||
| Line 13: | Line 12: | ||
* Wiring/Connectors from/to Left Parking Brake Motor (V282) faulty | * Wiring/Connectors from/to Left Parking Brake Motor (V282) faulty | ||
* Left Parking Brake Motor (V282) Power Supply faulty | * Left Parking Brake Motor (V282) Power Supply faulty | ||
| + | * Left Parking Brake Motor/Caliper (V282) faulty | ||
==== Possible Solutions ==== | ==== Possible Solutions ==== | ||
* Check Wiring/Connectors from/to Left Parking Brake Motor (V282) | * Check Wiring/Connectors from/to Left Parking Brake Motor (V282) | ||
| − | * Check Left Parking Brake Motor (V282) Power Supply | + | * Check Left Parking Brake Motor and (V282) Power Supply |
* Perform Terminal 30 Reset | * Perform Terminal 30 Reset | ||
** Remove Fuse(s) for a short Time. | ** Remove Fuse(s) for a short Time. | ||
| Line 23: | Line 23: | ||
==== Special Notes ==== | ==== Special Notes ==== | ||
| − | * | + | * When found in [[VW Passat (3C): Parking Brake]]: |
| − | * | + | ** Clear Fault Codes with Engine running (to ensure proper Voltage Supply). ''When checking Voltage with this Fault Code stored, the Module may not output Power to the Motor. Try clearing Fault Codes and Operating the EPB as mentioned below before testing again. |
| + | *** Switch Ignition OFF for about 10 Seconds | ||
| + | *** Start the Engine and keep it running while trying to clear Fault Codes. | ||
| + | *** Press the Parking Brake Button (E538) in 5 Second Intervals. | ||
| + | ** Check TPI 2013530 (Rest of World) or TSB 2015075/01-07-47 (North American Region) for possible Control Module Software Update which corrects Low Voltage Sensitivity. '''This Update can be considered mandatory if you have these Fault Codes stored!''' | ||
| + | __FORCETOC__ | ||
[[Category:Fault Codes]] | [[Category:Fault Codes]] | ||
Latest revision as of 05:03, 9 September 2011
02432 - Supply Voltage for Left Parking Brake Motor (V282)
02432 - Supply Voltage for Left Parking Brake Motor (V282): Electrical Fault in Circuit
02432 - Supply Voltage for Left Parking Brake Motor (V282): Open Circuit
Possible Symptoms
- Parking Brake Warning Light active/flashing
Possible Causes
- Wiring/Connectors from/to Left Parking Brake Motor (V282) faulty
- Left Parking Brake Motor (V282) Power Supply faulty
- Left Parking Brake Motor/Caliper (V282) faulty
Possible Solutions
- Check Wiring/Connectors from/to Left Parking Brake Motor (V282)
- Check Left Parking Brake Motor and (V282) Power Supply
- Perform Terminal 30 Reset
- Remove Fuse(s) for a short Time.
Special Notes
- When found in VW Passat (3C): Parking Brake:
- Clear Fault Codes with Engine running (to ensure proper Voltage Supply). When checking Voltage with this Fault Code stored, the Module may not output Power to the Motor. Try clearing Fault Codes and Operating the EPB as mentioned below before testing again.
- Switch Ignition OFF for about 10 Seconds
- Start the Engine and keep it running while trying to clear Fault Codes.
- Press the Parking Brake Button (E538) in 5 Second Intervals.
- Check TPI 2013530 (Rest of World) or TSB 2015075/01-07-47 (North American Region) for possible Control Module Software Update which corrects Low Voltage Sensitivity. This Update can be considered mandatory if you have these Fault Codes stored!
- Clear Fault Codes with Engine running (to ensure proper Voltage Supply). When checking Voltage with this Fault Code stored, the Module may not output Power to the Motor. Try clearing Fault Codes and Operating the EPB as mentioned below before testing again.