Difference between revisions of "ESP System Function Test"

From Ross-Tech Wiki
 
(17 intermediate revisions by 3 users not shown)
Line 1: Line 1:
−
== ESP System Function Test ==
+
== General ==
  
−
=== Notes ===
+
* The ESP System Function or Road Test serves to check the Plausibility of the Signals<br>from the Lateral Acceleration Sensor (G200), Rotation Rate Sensor (G202) and Brake Pressure Sensor (G201).
 +
* The ESP System Function Test should be performed after all major work on the Brake System, in some cases the Brake Electronics Control Module (J104) may automatically require this Function Test and set the correlating Fault Code [[01486]].
 +
* '''Once the Function Test has been started it cannot be cancelled and must be successfully finished.'''
 +
* ''The Diagnostic Tool should NOT need to be connected while performing the Function Test.''
  
−
* The ESP road test serves to check the plausibility of the signals from the lateral acceleration sender, rotation rate sender and pressure sender.
 
−
* It should always be carried out after removing or replacing any parts of the ESP system.
 
  
−
* '''It is not possible to cancel the ESP road test after it has been started. The complete test procedure must be performed.'''
+
Registered customers can  [mailto:Support@Ross-Tech.com contact us directly via email] for assistance completing the Function Test with a complete Auto-Scan and the repair history.  Our Techs have ''vast experience'' with this Subject and will gladly assist you with the Process. ''';-)'''
  
−
=== Pre-Conditions ===
 
  
−
* ABS/EDS Warning Light (K47) ON and ASR/ESP Indicator Light (K86) ON.
+
== Prerequisites ==
−
* Engine RUNNING.
+
* The ONLY fault that should be stored in the 03-ABS controller is [[01486]] and the 44-Steering Assist module should be fault-free.
−
* Vehicle standing.
+
* VCDS should NOT need to be connected while performing the Function Test!
 +
* Vehicle stationary
 +
* Ignition ON, Engine ON (Running)
 +
* Perform the Test Drive on an enclosed Site (i.e. a Parking Lot)
 +
* Make sure to Complete the Function Test within 50 Seconds after pressing the Brake Pedal
  
−
=== Instructions ===
+
== Instructions ==
  
−
* Press brake pedal firmly until the ASR/ESP Indicator Light (K86) goes OFF. A brake pressure of at least 35 bar needs to be reached for this.
+
* '''Firmly press the Brake Pedal until a certain Brake Pressure (usually right above 30 bar) is reached.'''
−
* Start road test (Do this on an enclosed site or make sure to drive according to traffic regulations).
+
* Brake Pressure Sensor (G201) Plausibility will be confirmed by a Change in the Brake Electronics Warning Lights.
−
* Make a right turn, then a left turn (or vice versa). A rotation rate (turn rate) of ~10 °/s must be reached while driving these turns.
+
** ''On '''Bosch''', the ASR/ESP Warning Light (K155) will switch OFF and the ABS Warning Light (K47) will switch ON.''
−
* The ABS/EDS Warning Light (K47) should now have turned OFF.
+
** ''On '''Continental/Teves''', the ABS Warning Light (K47) will switch OFF and the ASR/ESP Warning Light (K155) switch ON.''
 +
* '''Start Driving straight with a steady Speed of ~20 km/h (~13 mph).'''
 +
* '''Turn the Steering Wheel either Left or Right between a 90° Angle (1/4 Turn) to 180° Angle (1/2 Turn) and keep it steady.'''
 +
* Lateral Acceleration Sensor (G200) and Rotation Rate Sensor (G202) Plausibility is confirmed<br>once the remaining Brake Electronics Warning Light(s) switch OFF.
 +
* '''The Function Test is now completed.'''
  
−
* ''A common example for turns like this is driving turns with a radius of 10 to 12 meters (30 to 40 feet) with a speed of 15 to 30 kph (9 to 18 mph).''
+
== Notes ==
−
* ''The ABS, EDS, ASR and ESP functions may NOT get activated during these test.''
 
−
* ''Doing other maneuvers between the turns will have no influence on the ESP System Function Test.''
 
  
−
==== Special Notes ====
+
* When Driving, make sure the general Speed is between 15 to 30 kph (9 to 18 mph).
 +
* The Turn should be done at a Rotation/Turn Rate of ~10 °/s which can be achieved with a<br>Turning Radius of 10 to 12 Meters (30 to 40 feet) with a Speed between 15 to 30 kph (9 to 18 mph).
 +
* You may experience Variations in the Warning Light Behavior depending on the individual Brake System Generation,<br>this is no Reason to be concerned as long as you follow the General Procedure.
  
−
* When this cannot be completed on its own fault code 01486 may be stored. It may be necessary to enter Basic Settings, Group 103, Go.
+
 
 +
== Video Link ==
 +
 
 +
[[File:Systemfuntiontest_screengrab.jpg|200px|link=http://www.youtube.com/watch?v=7AVPRj2BNuc]]
 +
http://www.youtube.com/watch?v=7AVPRj2BNuc

Latest revision as of 11:10, 17 March 2016

General

  • The ESP System Function or Road Test serves to check the Plausibility of the Signals
    from the Lateral Acceleration Sensor (G200), Rotation Rate Sensor (G202) and Brake Pressure Sensor (G201).
  • The ESP System Function Test should be performed after all major work on the Brake System, in some cases the Brake Electronics Control Module (J104) may automatically require this Function Test and set the correlating Fault Code 01486.
  • Once the Function Test has been started it cannot be cancelled and must be successfully finished.
  • The Diagnostic Tool should NOT need to be connected while performing the Function Test.


Registered customers can contact us directly via email for assistance completing the Function Test with a complete Auto-Scan and the repair history. Our Techs have vast experience with this Subject and will gladly assist you with the Process. ;-)


Prerequisites

  • The ONLY fault that should be stored in the 03-ABS controller is 01486 and the 44-Steering Assist module should be fault-free.
  • VCDS should NOT need to be connected while performing the Function Test!
  • Vehicle stationary
  • Ignition ON, Engine ON (Running)
  • Perform the Test Drive on an enclosed Site (i.e. a Parking Lot)
  • Make sure to Complete the Function Test within 50 Seconds after pressing the Brake Pedal

Instructions

  • Firmly press the Brake Pedal until a certain Brake Pressure (usually right above 30 bar) is reached.
  • Brake Pressure Sensor (G201) Plausibility will be confirmed by a Change in the Brake Electronics Warning Lights.
    • On Bosch, the ASR/ESP Warning Light (K155) will switch OFF and the ABS Warning Light (K47) will switch ON.
    • On Continental/Teves, the ABS Warning Light (K47) will switch OFF and the ASR/ESP Warning Light (K155) switch ON.
  • Start Driving straight with a steady Speed of ~20 km/h (~13 mph).
  • Turn the Steering Wheel either Left or Right between a 90° Angle (1/4 Turn) to 180° Angle (1/2 Turn) and keep it steady.
  • Lateral Acceleration Sensor (G200) and Rotation Rate Sensor (G202) Plausibility is confirmed
    once the remaining Brake Electronics Warning Light(s) switch OFF.
  • The Function Test is now completed.

Notes

  • When Driving, make sure the general Speed is between 15 to 30 kph (9 to 18 mph).
  • The Turn should be done at a Rotation/Turn Rate of ~10 °/s which can be achieved with a
    Turning Radius of 10 to 12 Meters (30 to 40 feet) with a Speed between 15 to 30 kph (9 to 18 mph).
  • You may experience Variations in the Warning Light Behavior depending on the individual Brake System Generation,
    this is no Reason to be concerned as long as you follow the General Procedure.


Video Link

Systemfuntiontest screengrab.jpg http://www.youtube.com/watch?v=7AVPRj2BNuc

Retrieved from "http://wiki.ross-tech.com/wiki/index.php?title=ESP_System_Function_Test&oldid=7998"