Difference between revisions of "18447/P2015/008213"

From Ross-Tech Wiki
m (Sebastian moved page 16347/P2015 to 18447/P2015/008213 without leaving a redirect)
 
(4 intermediate revisions by 3 users not shown)
Line 1: Line 1:
 
__FORCETOC__
 
__FORCETOC__
  
−
== 16347/P2015 - Intake Manifold Flap Position Sensor (Bank 1)  ==
+
== 18447/P2015/008213 - Intake Manifold Flap Position Sensor (Bank 1): Implausible Signal ==
  
 
==== Possible Symptoms ====
 
==== Possible Symptoms ====
  
−
* MIL On
+
* Malfunction Indicator Light (MIL) ON
 +
* Power Loss
  
 
==== Possible Causes ====
 
==== Possible Causes ====
  
−
* Intake manifold "tumble flaps" sticking
+
* Intake Manifold Flap faulty
−
* Faulty intake manifold
+
* Intake Manifold Flap Motor (V157) stuck/faulty
−
* Failed V157 (Intake Flap Motor)  
+
* Engine Control Module Software/Firmware Version faulty
−
* ECM issue
+
* Wiring and/or Connector(s) from/to Intake Manifold Flap Motor (V157) faulty
−
* Wiring harness issue to V157
 
  
 
==== Possible Solutions ====
 
==== Possible Solutions ====
  
−
* Test wiring as per [[Official Factory Repair Information | Factory Repair Manual]]
+
* Check Intake Manifold Flap
−
* Run Output Tests to verify operation of the motor if it is electrically controlled.
+
* Check/Replace Intake Manifold Flap Motor (V157)
−
* Run Basic Settings ''when applicable'', which is common with Gasoline [[2.0l TFSI (AXX/BGB/BPJ/BPY/BWA) |2.0 TFSI]] engines.
+
** Perform Output Tests/Basic Setting
 +
* Check Wiring and/or Connector(s) from/to Intake Manifold Flap Motor (V157)
  
 
==== Special Notes ====
 
==== Special Notes ====
  
−
* In some cases the issue is being resolved by replacing the whole intake manifold.
+
* Check TSB 24-17-04 or 2045138 NAR) North American Region vehicles only.
−
* The V157 (Intake Flap Motor) and sensor G336 (Manifold Runner Position Sensor) are part of the same unit.
+
** 2006 - 2008 BPY and 2008 - 2016 CCTA and CBFA engines.
−
* Verify you have the latest version of the V157 unit and ECM firmware.
+
** Improved intake manifold design.
−
** VW (BRM 1.9L PD) TDI modules with the following SW (Software) part numbers are noted for issues:
+
** https://static.nhtsa.gov/odi/tsbs/2017/MC-10158548-9999.pdf  NHTSA
−
# 03G-906-016-AB with internal firmware # 7328.
+
* In some Cases the Issue can only be resolved by Replacing the whole Intake Manifold.
−
# 03G-906-016-AC with internal firmware # 7280.
+
* The Intake Manifold Flap Motor (V157) and Manifold Runner Position Sensor (G336) may be Part of the same Unit.
−
* The Firmware may also be referred to as the SWL (Software Level). This can be determined using VCDS by looking at the details in the [http://www.ross-tech.com/vcds/tour/open_screen.html Component] field.
+
* When found in a VW Golf/Jetta (1K): 1.9l PD-TDI (BRM), check Engine Control Module (ECM) Software Version:
−
 
+
** 03G-906-016-AB @ 7328 or 7550 as well as 03G-906-016-AC @ 7280 or 7551 do have a Software Error which requires a special Adaptation for the Intake Manifold Flap Motor (V157) which at this Point can only be performed with the Factory Tool.
 +
* This page describes a Basic Settings for some 2.0T gasoline engines: [[2.0l_TFSI_(AXX/BGB/BPJ/BPY/BWA)#Intake_Manifold_Runner]]
 +
* When found in North America Audi vehicles check Technical Service Bulletin number: 2044003
 +
** This TSB addresses possible issues with the N316 - Intake Manifold Flap Valve
 +
** https://static.nhtsa.gov/odi/tsbs/2016/SB-10093588-0699.pdf  NHTSA
  
 +
__FORCETOC__
 
[[Category:Fault Codes]]
 
[[Category:Fault Codes]]

Latest revision as of 11:36, 10 January 2022


18447/P2015/008213 - Intake Manifold Flap Position Sensor (Bank 1): Implausible Signal

Possible Symptoms

  • Malfunction Indicator Light (MIL) ON
  • Power Loss

Possible Causes

  • Intake Manifold Flap faulty
  • Intake Manifold Flap Motor (V157) stuck/faulty
  • Engine Control Module Software/Firmware Version faulty
  • Wiring and/or Connector(s) from/to Intake Manifold Flap Motor (V157) faulty

Possible Solutions

  • Check Intake Manifold Flap
  • Check/Replace Intake Manifold Flap Motor (V157)
    • Perform Output Tests/Basic Setting
  • Check Wiring and/or Connector(s) from/to Intake Manifold Flap Motor (V157)

Special Notes

  • Check TSB 24-17-04 or 2045138 NAR) North American Region vehicles only.
  • In some Cases the Issue can only be resolved by Replacing the whole Intake Manifold.
  • The Intake Manifold Flap Motor (V157) and Manifold Runner Position Sensor (G336) may be Part of the same Unit.
  • When found in a VW Golf/Jetta (1K): 1.9l PD-TDI (BRM), check Engine Control Module (ECM) Software Version:
    • 03G-906-016-AB @ 7328 or 7550 as well as 03G-906-016-AC @ 7280 or 7551 do have a Software Error which requires a special Adaptation for the Intake Manifold Flap Motor (V157) which at this Point can only be performed with the Factory Tool.
  • This page describes a Basic Settings for some 2.0T gasoline engines: 2.0l_TFSI_(AXX/BGB/BPJ/BPY/BWA)#Intake_Manifold_Runner
  • When found in North America Audi vehicles check Technical Service Bulletin number: 2044003
Retrieved from "http://wiki.ross-tech.com/wiki/index.php?title=18447/P2015/008213&oldid=9219"