Difference between revisions of "18447/P2015/008213"
From Ross-Tech Wiki
RtWiKiSyS0p (talk | contribs) |
|||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 24: | Line 24: | ||
==== Special Notes ==== | ==== Special Notes ==== | ||
| + | * Check TSB 24-17-04 or 2045138 NAR) North American Region vehicles only. | ||
| + | ** 2006 - 2008 BPY and 2008 - 2016 CCTA and CBFA engines. | ||
| + | ** Improved intake manifold design. | ||
| + | ** https://static.nhtsa.gov/odi/tsbs/2017/MC-10158548-9999.pdf NHTSA | ||
* In some Cases the Issue can only be resolved by Replacing the whole Intake Manifold. | * In some Cases the Issue can only be resolved by Replacing the whole Intake Manifold. | ||
* The Intake Manifold Flap Motor (V157) and Manifold Runner Position Sensor (G336) may be Part of the same Unit. | * The Intake Manifold Flap Motor (V157) and Manifold Runner Position Sensor (G336) may be Part of the same Unit. | ||
* When found in a VW Golf/Jetta (1K): 1.9l PD-TDI (BRM), check Engine Control Module (ECM) Software Version: | * When found in a VW Golf/Jetta (1K): 1.9l PD-TDI (BRM), check Engine Control Module (ECM) Software Version: | ||
** 03G-906-016-AB @ 7328 or 7550 as well as 03G-906-016-AC @ 7280 or 7551 do have a Software Error which requires a special Adaptation for the Intake Manifold Flap Motor (V157) which at this Point can only be performed with the Factory Tool. | ** 03G-906-016-AB @ 7328 or 7550 as well as 03G-906-016-AC @ 7280 or 7551 do have a Software Error which requires a special Adaptation for the Intake Manifold Flap Motor (V157) which at this Point can only be performed with the Factory Tool. | ||
| + | * This page describes a Basic Settings for some 2.0T gasoline engines: [[2.0l_TFSI_(AXX/BGB/BPJ/BPY/BWA)#Intake_Manifold_Runner]] | ||
| + | * When found in North America Audi vehicles check Technical Service Bulletin number: 2044003 | ||
| + | ** This TSB addresses possible issues with the N316 - Intake Manifold Flap Valve | ||
| + | ** https://static.nhtsa.gov/odi/tsbs/2016/SB-10093588-0699.pdf NHTSA | ||
__FORCETOC__ | __FORCETOC__ | ||
[[Category:Fault Codes]] | [[Category:Fault Codes]] | ||
Latest revision as of 11:36, 10 January 2022
18447/P2015/008213 - Intake Manifold Flap Position Sensor (Bank 1): Implausible Signal
Possible Symptoms
- Malfunction Indicator Light (MIL) ON
- Power Loss
Possible Causes
- Intake Manifold Flap faulty
- Intake Manifold Flap Motor (V157) stuck/faulty
- Engine Control Module Software/Firmware Version faulty
- Wiring and/or Connector(s) from/to Intake Manifold Flap Motor (V157) faulty
Possible Solutions
- Check Intake Manifold Flap
- Check/Replace Intake Manifold Flap Motor (V157)
- Perform Output Tests/Basic Setting
- Check Wiring and/or Connector(s) from/to Intake Manifold Flap Motor (V157)
Special Notes
- Check TSB 24-17-04 or 2045138 NAR) North American Region vehicles only.
- 2006 - 2008 BPY and 2008 - 2016 CCTA and CBFA engines.
- Improved intake manifold design.
- https://static.nhtsa.gov/odi/tsbs/2017/MC-10158548-9999.pdf NHTSA
- In some Cases the Issue can only be resolved by Replacing the whole Intake Manifold.
- The Intake Manifold Flap Motor (V157) and Manifold Runner Position Sensor (G336) may be Part of the same Unit.
- When found in a VW Golf/Jetta (1K): 1.9l PD-TDI (BRM), check Engine Control Module (ECM) Software Version:
- 03G-906-016-AB @ 7328 or 7550 as well as 03G-906-016-AC @ 7280 or 7551 do have a Software Error which requires a special Adaptation for the Intake Manifold Flap Motor (V157) which at this Point can only be performed with the Factory Tool.
- This page describes a Basic Settings for some 2.0T gasoline engines: 2.0l_TFSI_(AXX/BGB/BPJ/BPY/BWA)#Intake_Manifold_Runner
- When found in North America Audi vehicles check Technical Service Bulletin number: 2044003
- This TSB addresses possible issues with the N316 - Intake Manifold Flap Valve
- https://static.nhtsa.gov/odi/tsbs/2016/SB-10093588-0699.pdf NHTSA