Difference between revisions of "Bentley Continental (3W) Brake Electronics (Bosch 8.1)"
(Created page with "__FORCETOC__ == Security Access == '''''Note #1''': After the Security Access - 16 (Login) has been carried out you need to Recode the control module then perform the Steerin...") |
|||
| (2 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
__FORCETOC__ | __FORCETOC__ | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
== Coding == | == Coding == | ||
| − | + | Registered users can email us directly with a complete Auto-Scan for assistance coding this module. | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
== Basic Setting == | == Basic Setting == | ||
| Line 25: | Line 10: | ||
Before starting the procedure turn the steering wheel at least 30 ° left and back straight ahead.<br> | Before starting the procedure turn the steering wheel at least 30 ° left and back straight ahead.<br> | ||
| + | Verify the steering wheel is centered by moving the vehicle moving straight ahead (less than 20KMH/15MPH).<br> | ||
| + | |||
'''[Meas. Blocks - 08]'''<br> | '''[Meas. Blocks - 08]'''<br> | ||
| Line 40: | Line 27: | ||
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
| + | |||
| + | '''[Fault Codes - 02]'''<br> | ||
| + | All fault codes should have disappeared.<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | |||
| + | '''[Close Controller, Go Back - 06]'''<br> | ||
| + | |||
| + | |||
| + | === ESP-Sensor Unit (G419) === | ||
| + | |||
| + | '''[Select]'''<br> | ||
| + | '''[03 - ABS Brakes]'''<br> | ||
| + | |||
| + | '''[Security Access - 16]'''<br> | ||
| + | Enter 40168<br> | ||
| + | '''[Do It!]'''<br> | ||
| + | |||
| + | '''[Basic Settings - 04]'''<br> | ||
| + | Group 069<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Field 2 should show '''OK''' after a successful Calibration.<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | |||
| + | '''[Meas. Blocks - 08]'''<br> | ||
| + | Group 010 Field 1/2 (Longitudinal Acceleration Sensor (G251))<br> | ||
| + | Specification: ±1.25 m/s²<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | |||
'''[Fault Codes - 02]'''<br> | '''[Fault Codes - 02]'''<br> | ||
Latest revision as of 15:21, 10 March 2023
Coding
Registered users can email us directly with a complete Auto-Scan for assistance coding this module.
Basic Setting
Steering Angle Sensor (G85) Calibration
Before starting the procedure turn the steering wheel at least 30 ° left and back straight ahead.
Verify the steering wheel is centered by moving the vehicle moving straight ahead (less than 20KMH/15MPH).
[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]
[Security Access - 16]
Enter 40168
[Do It!]
[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]
[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]
[Close Controller, Go Back - 06]
ESP-Sensor Unit (G419)
[Select]
[03 - ABS Brakes]
[Security Access - 16]
Enter 40168
[Do It!]
[Basic Settings - 04]
Group 069
[Go!]
Field 2 should show OK after a successful Calibration.
[Done, Go Back]
[Meas. Blocks - 08]
Group 010 Field 1/2 (Longitudinal Acceleration Sensor (G251))
Specification: ±1.25 m/s²
[Done, Go Back]
[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]
[Close Controller, Go Back - 06]