Difference between revisions of "P119A/004506"
From Ross-Tech Wiki
| (8 intermediate revisions by 4 users not shown) | |||
| Line 11: | Line 11: | ||
* Wiring and/or Connector(s) from/to Fuel Pressure Sensor (G247) | * Wiring and/or Connector(s) from/to Fuel Pressure Sensor (G247) | ||
* Faulty HPFP | * Faulty HPFP | ||
| + | * Faulty (leaking) fuel injector | ||
| + | * Exhaust Leak (sounds strange, but check for one!) | ||
==== Possible Solutions ==== | ==== Possible Solutions ==== | ||
| Line 17: | Line 19: | ||
* Check Wiring and/or Connector(s) from/to Fuel Pressure Sensor (G247) | * Check Wiring and/or Connector(s) from/to Fuel Pressure Sensor (G247) | ||
* Replace HPFP | * Replace HPFP | ||
| + | * Check fuel injectors for leak-down | ||
| + | * Fix exhaust leak if one is found. | ||
==== Special Notes ==== | ==== Special Notes ==== | ||
* The Fuel Pressure Regulator Valve (N276) or Fuel Metering valve (N290) on the HPFP can fail. | * The Fuel Pressure Regulator Valve (N276) or Fuel Metering valve (N290) on the HPFP can fail. | ||
| − | ** (N276) ''Fuel Pressure Regulating Valve'' resistance should be approximately 1 to 5 Ω | + | ** (N276) ''Fuel Pressure Regulating Valve'' resistance should be approximately 1 to 5 Ω * |
| − | ** (N290) ''Fuel Metering valve'' resistance should be approximately 0.8 to 5 Ω | + | ** (N290) ''Fuel Metering valve'' resistance should be approximately 0.8 to 5 Ω * |
| + | ** ''(* always refer to repair manuals for specific values for your engine)'' | ||
| + | * If found with a TFSI engine and [[16555/P0171/000369]] - Fuel Trim; Bank 1: System Too Lean is also flagged, this could be caused by a failed rear main seal. | ||
| + | ** [http://forums.ross-tech.com/showthread.php?2612-TFSI-Oil-leak-Not-a-VCDS-releated-question-or-is-it TFSI - Oil leak - TFSI - Oil leak - Not a VCDS related question? or is it? ] | ||
__FORCETOC__ | __FORCETOC__ | ||
[[Category:Fault Codes]] | [[Category:Fault Codes]] | ||
Latest revision as of 09:26, 16 August 2024
P119A/004506 - Fuel Pressure Sensor (G247) : Malfunction
Possible Symptoms
- Malfunction Indicator Light (MIL) active
- Reduced fuel economy and engine performance
Possible Causes
- Faulty Fuel Pressure Sensor (G247)
- Wiring and/or Connector(s) from/to Fuel Pressure Sensor (G247)
- Faulty HPFP
- Faulty (leaking) fuel injector
- Exhaust Leak (sounds strange, but check for one!)
Possible Solutions
- Replace Fuel Pressure Sensor (G247)
- Check Wiring and/or Connector(s) from/to Fuel Pressure Sensor (G247)
- Replace HPFP
- Check fuel injectors for leak-down
- Fix exhaust leak if one is found.
Special Notes
- The Fuel Pressure Regulator Valve (N276) or Fuel Metering valve (N290) on the HPFP can fail.
- (N276) Fuel Pressure Regulating Valve resistance should be approximately 1 to 5 Ω *
- (N290) Fuel Metering valve resistance should be approximately 0.8 to 5 Ω *
- (* always refer to repair manuals for specific values for your engine)
- If found with a TFSI engine and 16555/P0171/000369 - Fuel Trim; Bank 1: System Too Lean is also flagged, this could be caused by a failed rear main seal.