Difference between revisions of "00288"
From Ross-Tech Wiki
| (4 intermediate revisions by 3 users not shown) | |||
| Line 30: | Line 30: | ||
** This will wake-up(activate) the CAN-Bus and may allow limited communication to the vehicle | ** This will wake-up(activate) the CAN-Bus and may allow limited communication to the vehicle | ||
** If present clear the N360 fault code and if the vehicle's ignition power is now active, suspect a failed N360. | ** If present clear the N360 fault code and if the vehicle's ignition power is now active, suspect a failed N360. | ||
| + | * When found in the Volkswagen Passat 3C, please see this page [[VW Passat (3C) Immobilizer]] | ||
* When found on the [[Audi A6/S6/RS6/allroad (4F)]] the N360 is part of the steering column and is not available separately from the Audi at this time. | * When found on the [[Audi A6/S6/RS6/allroad (4F)]] the N360 is part of the steering column and is not available separately from the Audi at this time. | ||
| − | * See TSB / TPI 2040593 for possible part/software update when found in Audi Q7 and A6 (2005 to | + | * See TSB / TPI 2040593 for possible part/software update when found in Audi Q7 and A6 (2005 to 2015). |
| − | * Vehicles equipped with Immobilizer 4C or higher will require an online connection with VW/Audi/Bentley to correctly adapt the new N360 to the vehicle. | + | ** https://static.nhtsa.gov/odi/tsbs/2015/MC-10120042-9999.pdf NHTSA |
| − | * Replacement with a used N360 is not | + | * Vehicles equipped with Immobilizer 4C or higher will require an online connection with VW/Audi/Bentley to correctly adapt the new N360 to the vehicle. erWin offers some Immobilizer and Pass-Thru solutions which are mentioned under the notes section of our [[Official Factory Repair Information]] page. |
| + | * Replacement with a used N360 is not supported. | ||
[[Category:Fault Codes]] | [[Category:Fault Codes]] | ||
Latest revision as of 14:43, 19 March 2021
00288 - Steering Column Lock Actuator (N360)
00288 - Steering Column Lock Actuator (N360): No Signal
00288 - Steering Column Lock Actuator (N360): Implausible signal
00288 - Steering Column Lock Actuator (N360): Open Circuit
00288 - Steering Column Lock Actuator (N360):Open Circuit / Short to ground
00288 - Steering Column Lock Actuator (N360): Open Circuit / Short to positive
00288 - Steering Column Lock Actuator (N360): Electrical fault in Circuit
00288 - Steering Column Lock Actuator (N360): Defective
Possible Symptoms
- Ignition power will NOT switch on
- Steering column will or will not lock
Possible Causes
- Wiring/Connections from/to N360
- Faulty N360
Possible Solutions
- Check wiring/connections from/to N360
- Check/Replace failed N360
Special Notes
- If the ignition will not switch on, the communication with the Access Start controller still maybe possible, Try this:
- Turn on the hazards, press the brake pedal and hold the flash to pass
- This will wake-up(activate) the CAN-Bus and may allow limited communication to the vehicle
- If present clear the N360 fault code and if the vehicle's ignition power is now active, suspect a failed N360.
- When found in the Volkswagen Passat 3C, please see this page VW Passat (3C) Immobilizer
- When found on the Audi A6/S6/RS6/allroad (4F) the N360 is part of the steering column and is not available separately from the Audi at this time.
- See TSB / TPI 2040593 for possible part/software update when found in Audi Q7 and A6 (2005 to 2015).
- Vehicles equipped with Immobilizer 4C or higher will require an online connection with VW/Audi/Bentley to correctly adapt the new N360 to the vehicle. erWin offers some Immobilizer and Pass-Thru solutions which are mentioned under the notes section of our Official Factory Repair Information page.
- Replacement with a used N360 is not supported.