Difference between revisions of "Immobilizer IV Immobilizer Swapping (Instrument Cluster)"
RtWiKiSyS0p (talk | contribs) m |
RtWiKiSyS0p (talk | contribs) m |
||
Line 31: | Line 31: | ||
* The NEW (USED) cluster is installed in the car. | * The NEW (USED) cluster is installed in the car. | ||
* Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster. | * Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster. | ||
− | * Battery voltage at least 12.0 V. | + | * Battery voltage at least 12.0 V. |
− | + | * All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster. | |
'''[Select]'''<br> | '''[Select]'''<br> |
Revision as of 09:08, 1 June 2006
This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer IV.
Determining IMMO-ID & VIN (ECU)
[Select]
[01 - Engine]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]
Determining IMMO-ID & VIN (Instrument Cluster)
[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]
Instrument Cluster Swapping (Used Cluster)
Prerequisites:
- The NEW (USED) cluster is installed in the car.
- Make sure to have BOTH PIN's, from the OLD (ORIGINAL) and the NEW (USED) instrument cluster.
- Battery voltage at least 12.0 V.
- All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW (USED) cluster.
[Select]
[25 - Immobilizer]
[Security Access - 16]
For the following procedure, use the PIN of the NEW (USED) instrument cluster.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.
- 4-digit PIN
- Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
- 7-digit PIN
- [Use 7-digit PIN/SKC]
- Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
- [OK]
- VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
[Do it!]
[Adaptation - 10]
Enter 050 in "Channel Number".
[Read]
For the following procedure, use the PIN of the OLD (ORIGINAL) instrument cluster.
There are 2 possibilities how to enter a PIN, choose the one that applies for you.
- 4-digit PIN
- Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
- 7-digit PIN
- [Use 7-digit PIN/SKC]
- Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
- [OK]
- VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]
- Switch OFF the ignition and let the car sit for ~1 minute, then switch ON the ignition again.
- Verify that the NEW (USED) instrument cluster now shows the VIN/IMMO-ID of the vehicle now.
- Proceed with Key Matching now.