VW Passat (3B) Brake Electronics (Bosch 5.7)

Login

Note #1: After Login has been carried out you need to recode the control module.
Note #2: The PR codes ( such as 1LJ ) can be found in a sticker near the spare tire well. Click this link to see an example of a sticker

• 0?xxx: Chassis
  • 8 = VW Passat W8
  • 9 = VW Passat
• 0x?xx: Brakes
  • 3 = (PR-1LT/1LF)
  • 4 = (PR-1LC/1LX/1ZF/1LZ/1ZG)
  • 5 = (PR-1LB/1LE/1ZC)
  • 6 = (PR-1LZ/1ZJ)
• 0xx?x: Engine
  • 5 = (PR-T5X/T4N/T9J*/T6T/T1K/T1E/T7F*) (* with Brakes: PR-1LB/1LE/1ZC)
  • 7 = (PR-T0B/T10/T6V/T0D/T0F)
  • 9 = (PR-T7F/T9H/T9J)
• 0xxx?: Transmission
  • 5 = Manual (PR-G0C/G0K/G0G/G0L)
  • 7 = Automatic (PR-G0E/G0F/G0Q)

Coding

Note #1: Coding is accepted after a specific login has been carried out.
Note #2: After successful coding the steering angle sensor basic setting needs to be carried out.
Note #3: The PR codes ( such as 1LE ) can be found in a sticker near the spare tire well.

• 0?xxx: Chassis
  • 4 = VW Passat
  • 5 = VW Passat W8
• 0x?xx: Brakes
  • 1 = (PR-1LZ/1ZJ)
  • 2 = (PR-1LB/1LE/1ZC)
  • 3 = (PR-1LC/1LX/1ZF/1LZ/1ZG)
  • 4 = (PR-1LT/1LF)
• 0xx?x: Engine
  • 5 = (PR-T5X/T4N/T9J*/T6T/T1K/T1E/T7F*) (* with Brakes: PR-1LB/1LE/1ZC)
  • 7 = (PR-T0B/T10/T6V/T0D/T0F)
  • 9 = (PR-T7F/T9H/T9J)
• 0xxx?: Transmission
  • 5 = Manual (PR-G0C/G0K/G0G/G0L)
  • 7 = Automatic (PR-G0E/G0F/G0Q)

Basic Setting

Steering Angle Sensor (G85) Calibration

Note: A successful calibration usually requires a correct coding, so make sure the control module is correctly coded first.

[Select]
[03 - ABS Brakes]

[Fault Codes - 02]
[Done, Go Back]

Turn steering wheel at least 30 ° left and back straight ahead.

[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]

[Login - 11]
Enter 40168
[Do It!]

[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]

[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]

[Close Controller, Go Back - 06]