Difference between revisions of "User:Peter"
From Ross-Tech Wiki
| Line 2: | Line 2: | ||
| − | '''Prerequisites:'''<br> | + | '''<u>Prerequisites:</u>'''<br> |
| − | + | * Battery Voltage = 12.0 - 14.0 V'''<br> | |
| − | + | * No fault codes other than [[01087 | 01087 - Basic Setting Not Performed]]'''<br> | |
| − | + | * Vehicle is lifted off the ground, on a suitable vehicle lift'''<br> | |
| Line 12: | Line 12: | ||
'''[Meas. Blocks - 08]'''<br> | '''[Meas. Blocks - 08]'''<br> | ||
Note: The values stored in the Measuring Value Blocks below are the Minimum and Maximum sensor values.'''<br> | Note: The values stored in the Measuring Value Blocks below are the Minimum and Maximum sensor values.'''<br> | ||
| − | Group-054 Field-1 = G78 - Min value'''<br> | + | * Group-054 Field-1 = G78 - Min value'''<br> |
| − | Group-054 Field-2 = G78 - Max value'''<br> | + | * Group-054 Field-2 = G78 - Max value'''<br> |
<br> | <br> | ||
| − | Group-055 Field-1 = G289 - Min value'''<br> | + | * Group-055 Field-1 = G289 - Min value'''<br> |
| − | Group-055 Field-2 = G289 - Max value'''<br> | + | * Group-055 Field-2 = G289 - Max value'''<br> |
<br> | <br> | ||
'''Look at:'''<br> | '''Look at:'''<br> | ||
| − | '''Group-003 - Field-1,2,3 - Actual Sensor values'<br> | + | '''Group-003 - Field-1,2,3 - Actual Sensor values'''<br> |
| − | + | * If the values are with in the range of the Min - Max stored values from MVBs 054 and 055 then Basic settings can be performed, if not inspect suspension or sensors.'''<br> | |
| − | Basic settings can be performed, if not inspect suspension or sensors.'''<br> | ||
<br> | <br> | ||
'''[Security Access - 16]'''<br> | '''[Security Access - 16]'''<br> | ||
| Line 27: | Line 26: | ||
'''[Do it!]'''<br> | '''[Do it!]'''<br> | ||
'''[Basic Settings - 04]'''<br> | '''[Basic Settings - 04]'''<br> | ||
| − | + | Group 001<br> | |
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
<br> | <br> | ||
The New values should be displayed.'''<br> | The New values should be displayed.'''<br> | ||
| − | + | * To check the learned values, check Measuring Value Group-008.'''<br> | |
| − | [Meas. Blocks - 08]'''<br> | + | '''[Meas. Blocks - 08]'''<br> |
| − | + | Group 008<br> | |
| + | '''[Go!]'''<br> | ||
The values displayed should be the learned values as displayed in the Basic Settings window.'''<br> | The values displayed should be the learned values as displayed in the Basic Settings window.'''<br> | ||
Revision as of 10:18, 30 May 2013
Electronic Damping Control J250 - Basic Settings
Prerequisites:
- Battery Voltage = 12.0 - 14.0 V
- No fault codes other than 01087 - Basic Setting Not Performed
- Vehicle is lifted off the ground, on a suitable vehicle lift
[Select]
[14 - Susp. Elect]
[Meas. Blocks - 08]
Note: The values stored in the Measuring Value Blocks below are the Minimum and Maximum sensor values.
- Group-054 Field-1 = G78 - Min value
- Group-054 Field-2 = G78 - Max value
- Group-055 Field-1 = G289 - Min value
- Group-055 Field-2 = G289 - Max value
Look at:
Group-003 - Field-1,2,3 - Actual Sensor values
- If the values are with in the range of the Min - Max stored values from MVBs 054 and 055 then Basic settings can be performed, if not inspect suspension or sensors.
[Security Access - 16]
Enter 31564, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 001
[Go!]
The New values should be displayed.
- To check the learned values, check Measuring Value Group-008.
[Meas. Blocks - 08]
Group 008
[Go!]
The values displayed should be the learned values as displayed in the Basic Settings window.