|
|
| Line 27: |
Line 27: |
| * While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.'' | | * While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.'' |
| * Battery voltage at least 12.5 V.<br> | | * Battery voltage at least 12.5 V.<br> |
|
| |
|
| |
| '''[Select]'''<br>
| |
| '''[17 - Instruments]'''<br>
| |
| ''Write down the 14 digit Immobilizer ID number from the "Extra" field''<br>
| |
| '''[Meas. Blocks - 08]'''<br>
| |
| Select Block 002.<br>
| |
| '''[Go!]'''<br>
| |
| ''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br>
| |
| ''You can check each key in this manner.''
| |
|
| |
| 1.
| |
|
| |
| [Select]
| |
| [17 - Instruments]
| |
| Write down the 14 digit Immobilizer ID number from the "Extra" field
| |
|
| |
| 2.
| |
|
| |
| Take that ID number to your dealer and request your seven-digit SKC, along with the workshop code and importer number (all this information can be found in the upper-right corner of the Administration screen of the dealer's VAS 5051). Additional information about how to find the WSC and Importer Number can be found here.
| |
|
| |
| 3.
| |
|
| |
| Measure the car's battery voltage, it must be 12.5 V or higher.
| |
|
| |
| 4.
| |
|
| |
| You can check to make sure a key has the correct electronics in it so that it can be matched to the Immobilizer by:
| |
| [Select]
| |
| [17 - Instruments]
| |
| [Meas. Blocks - 08]
| |
| Group 022
| |
| [Go!]
| |
| The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer. You can check each key in this manner.
| |
|
| |
| 5.
| |
|
| |
| [Select]
| |
| [17 - Instruments]
| |
| [Meas. Blocks - 08]
| |
| Group 024
| |
| [Go!]
| |
| Any numbers displayed in fields 1-4 represent the time in minutes that must be counted down before the Immobilizer is unlocked. If the fields are all zero, skip to step 6. If the Immobilizer is locked:
| |
| [Done, Go Back]
| |
| [Close Controller, Go Back - 06]
| |
| Do not switch off the ignition! Allow the car to sit for AT LEAST the number of minutes that were indicated by the display in Group 024
| |
|
| |
| 6.
| |
|
| |
| [Select]
| |
| [17 - Instruments]
| |
| [Meas. Blocks - 08]
| |
| Group 024
| |
| [Go!]
| |
| Make sure all fields are zero.
| |
| [Done, Go Back]
| |
|
| |
| 7.
| |
|
| |
| [Login - 11]
| |
| [Use 7-digit PIN/SKC]
| |
| Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
| |
| [OK]
| |
|
| |
| 8.
| |
|
| |
| VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
| |
| [Do It!]
| |
|
| |
| 9.
| |
|
| |
| [Adaptation - 10]
| |
| Enter 21 in "Channel Number"
| |
| [Read]
| |
| The "Stored Value" is the number of keys currently matched.
| |
| Enter "new value" of 0
| |
| [Save]
| |
| This clears out the old key-matchings.
| |
| Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys
| |
| [Save]
| |
|
| |
| 10.
| |
|
| |
| [Done, Go Back]
| |
| [Close Controller, Go Back - 06]
| |
| Switch ignition off and remove key
| |
|
| |
| 11.
| |
|
| |
| Insert next key to ignition and switch ignition on again
| |
| The warning light for the Immobilizer will light up for ~2 seconds, then go out
| |
| Switch ignition off and remove key
| |
|
| |
| 12.
| |
|
| |
| Repeat step 11 with each key until all keys have been matched.
| |
|
| |
|
| |
|
| |
| '''[Select]'''<br>
| |
| '''[25 - Immobilizer]'''<br>
| |
| '''[Meas. Blocks - 08]'''<br>
| |
| Select Block 002.<br>
| |
| '''[Go!]'''<br>
| |
| ''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br>
| |
| ''You can check each key in this manner.''
| |
|
| |
|
| |
| Select Block 003.<br>
| |
| '''[Go!]'''<br>
| |
| ''Make sure the shown lock times in field 1, 2 and 3 are '''0''' (each field represents a time in minutes).''<br>
| |
| * ''If the lock times are NOT '''0''':''
| |
| ** ''Do NOT switch off the ignition!''
| |
| ** ''Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.''
| |
| '''[Done, Go Back]'''<br>
| |
|
| |
|
| |
| '''[Security Access - 16]'''<br>
| |
| ''There are 2 possibilities how to enter a PIN, choose the one that applies for you.''
| |
| * '''4-digit PIN'''
| |
| ** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.''
| |
| * '''7-digit PIN'''
| |
| ** '''[Use 7-digit PIN/SKC]'''
| |
| ** Enter the 7-digit PIN, Date on which the PIN was generated by the dealer, along with the Workshop Code (WSC) and the Importer number of the dealer that generated the code.
| |
| ** '''[OK]'''
| |
| ** VAG-COM will validate the data you have entered and return you to the Login screen, where the Login Code will show as "XXXXX".
| |
| '''[Do it!]'''<br>
| |
|
| |
|
| |
| '''[Adaptation - 10]'''<br>
| |
| Enter 001 in "Channel Number".<br>
| |
| '''[Read]'''<br>
| |
| ''The "Stored Value" is the number of keys currently matched.''<br>
| |
| Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br>
| |
| ''The old keys are automatically beeing cleared.''<br>
| |
| '''[Save]'''<br>
| |
| '''[Done, Go Back]'''
| |
| '''[Close Controller, Go Back - 06]'''
| |
|
| |
|
| |
| * ''Repeat the following steps until all keys have been matched:''<br>
| |
| **''Switch ignition off and remove key.''<br>
| |
| **''Insert next key to ignition and switch ignition on again.''<br>
| |
| **''The warning light for the Immobilizer will light up for ~2 seconds, then go out Switch ignition off and remove key.''<br>
| |
|
| |
| '''Note:''' ''The above steps after saving the adaptation, should not exceed 60 seconds!''
| |
This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer III.
Determining IMMO-ID & VIN
[Select]
[17 - Instruments] or in vehicles with separate Immobilizer [25 - Immobilizer]
“Look at the first "Extra" field. If you see something like: Immo-ID VWZ7Z0W0648696" then you've got Immo-II (or maybe even Immo-1 in earlier non-US models).If you see something like WVZKB58001H231169 VWZ7Z0W0648696 then you've got Immo-III. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID. “
[Close Controller, Go Back - 06]
---OR---
[Select]
[25 - Immobilizer]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]
Key Matching
Prerequisites:
- While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place.
- Battery voltage at least 12.5 V.
