Immobilizer II Immobilizer Swapping (Instrument Cluster): Difference between revisions
Table Of Contents
No edit summary |
|||
| Line 20: | Line 20: | ||
Note: If the 17 Digit VIN is shown the vehicle does not use Immo II and the procedure here does not apply. | Note: If the 17 Digit VIN is shown the vehicle does not use Immo II and the procedure here does not apply. | ||
== Instrument Cluster Swapping | == Instrument Cluster Swapping == | ||
'''<u>Prerequisites:</u>'''<br> | '''<u>Prerequisites:</u>'''<br> | ||
* The Coding from the OLD ( | * The Coding from the OLD (ORIGINAL) cluster has been saved. | ||
* The NEW | * The REPLACEMENT (NEW or USED) cluster is installed in the car. | ||
* Battery voltage at least 12.0 V. | * Battery voltage at least 12.0 V. | ||
* All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the NEW | * All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the REPLACEMENT (NEW or USED) cluster. | ||
* Make sure to have the PIN for the NEW | * Make sure to have the PIN for the REPLACEMENT (NEW or USED) instrument cluster. | ||
* Make sure to have the Radio Code (for factory radios only).<br> | * Make sure to have the Radio Code (for factory radios only).<br> | ||
| Line 35: | Line 35: | ||
'''[17 - Instruments]'''<br> | '''[17 - Instruments]'''<br> | ||
'''[Recode - 07]'''<br> | '''[Recode - 07]'''<br> | ||
Enter the coding from the OLD ( | Enter the coding from the OLD (ORIGINAL) cluster<br> | ||
'''[Do It!]'''<br> | '''[Do It!]'''<br> | ||
| Line 44: | Line 44: | ||
'''[19 - CAN Gateway]'''<br> | '''[19 - CAN Gateway]'''<br> | ||
'''[Coding - 07]'''<br> | '''[Coding - 07]'''<br> | ||
Enter the coding from the OLD ( | Enter the coding from the OLD (ORIGINAL) cluster<br> | ||
'''[Do It!]'''<br> | '''[Do It!]'''<br> | ||
| Line 75: | Line 75: | ||
* Instructions for mileage entry on a new instrument cluster can be found here: [http://www.ross-tech.com/vag-com/cars/Immo2-cluster-swapping.html Procedure for installing a NEW Instrument Cluster in vehicles with Immobilizer II] | * Instructions for mileage entry on a new instrument cluster can be found here: [http://www.ross-tech.com/vag-com/cars/Immo2-cluster-swapping.html Procedure for installing a NEW Instrument Cluster in vehicles with Immobilizer II] | ||
** Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value! | ** Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value! | ||
** VCDS can not alter or "correct" the odometer reading of a used instrument cluster. | |||
Latest revision as of 21:24, 12 July 2012
This procedure details how to change the instrument cluster on VW/Audi/Seat/Skoda vehicles with Immobilizer II, where the immobilizer control module is integrated in instrument cluster.
Determining IMMO-ID (ECU)
[Select]
[01 - Engine]
Look at the first "Extra" field. The 14-digit string is the Immo-ID.
[Close Controller, Go Back - 06]
Note: If the 17 Digit VIN is shown the vehicle does not use Immo II and the procedure here does not apply.
Determining IMMO-ID (Instrument Cluster)
[Select]
[17 - Instruments]
Look at the first "Extra" field. The 14-digit string is the Immo-ID.
[Close Controller, Go Back - 06]
Note: If the 17 Digit VIN is shown the vehicle does not use Immo II and the procedure here does not apply.
Instrument Cluster Swapping
Prerequisites:
- The Coding from the OLD (ORIGINAL) cluster has been saved.
- The REPLACEMENT (NEW or USED) cluster is installed in the car.
- Battery voltage at least 12.0 V.
- All relevant coding and adaptation values have been transferred from the OLD (ORIGINAL) cluster to the REPLACEMENT (NEW or USED) cluster.
- Make sure to have the PIN for the REPLACEMENT (NEW or USED) instrument cluster.
- Make sure to have the Radio Code (for factory radios only).
Coding
[Select]
[17 - Instruments]
[Recode - 07]
Enter the coding from the OLD (ORIGINAL) cluster
[Do It!]
Additional Volkswagen Step Including models with an Integral Address 19 - CAN Gateway in the Cluster
[Select]
[19 - CAN Gateway]
[Coding - 07]
Enter the coding from the OLD (ORIGINAL) cluster
[Do It!]
Additional Audi Step Including vehicles that Do Not use an Integral Address 19 - CAN Gateway in the Cluster
Additional Adaptation Channels may be needed for SRI and the Internal Installation List of installed modules.
- The Internal Installation List channels are generally 060, 061 and 062 when applicable.
- The SRI channels vary by cluster. The automated SRI Reset feature of VCDS can be used to check the settings.
Matching the Cluster to the Engine ECU
[Select]
[17 - Instruments]
[Adaption - 10]
Leave channel at "00"
[Read]
[Save]
[Done, Go Back]
[Close Controller, Go Back - 06]
Switch ignition Off and then back On within one minute, but do not start vehicle.
Notes: On some Euro Audi models with Immobilizer II, a PIN will be required.
Proceed with Key Matching (through Instrument Cluster) now.
Special Notes
- Instructions for mileage entry on a new instrument cluster can be found here: Procedure for installing a NEW Instrument Cluster in vehicles with Immobilizer II
- Please note the Country Coding and Kilometer -or- Mile units prior to saving the adaptation value!
- VCDS can not alter or "correct" the odometer reading of a used instrument cluster.
No categories.