Difference between revisions of "Audi CAN Gateway Battery Coding (8T/8K/8R+)"
| Line 10: | Line 10: | ||
=== Long Adaptation === | === Long Adaptation === | ||
| − | Installation of a new battery requires the use of the [http://www.ross-tech.com/vcds/tour/adaptation_screen.html#long Long Adaptation] function under 19-CAN-Gateway control module. Follow the onscreen instructions to enter the Part Number, Vendor, and Serial Number all as one long new value. | + | Installation of a new battery requires the use of the [http://www.ross-tech.com/vcds/tour/adaptation_screen.html#long [Long Adaptation-0A]] function under 19-CAN-Gateway control module. Follow the onscreen instructions to enter the Part Number, Vendor, and Serial Number all as one long new value. |
| + | '''<u>Prerequisites:</u>'''<br> | ||
| + | * New Audi Battery Installed | ||
| + | ** Aftermarket batteries may NOT have a valid Audi Part Number, Vendor code or Serial number. Ross-Tech cannot offer assistance if the necessary information is missing. | ||
| + | * Key On, Engine OFF | ||
| + | <br> | ||
| + | '''[Select]'''<br> | ||
| + | '''[19 - CAN-Gateway]'''<br> | ||
| + | '''[Long Adaptation-0A]'''<br> | ||
| + | Channel 004<br> | ||
| + | '''[Read]'''<br> | ||
| + | VCDS will populate instructions in the form of a pop-up balloon with the formatting. For example: | ||
| + | Format: NNNNNNNNNNN XXX ZZZZZZZZZZ | ||
| + | |||
| + | N = Battery Part Number (11 Digits) | ||
| + | X = Battery Vendor (3 Digits) | ||
| + | Z = Battery Serial Number (10 Digits) | ||
| + | |||
| + | '''[Add to Log]''' ''Saving the original value to a log is strongly recommended''.<br> | ||
| + | Type the New Battery details into the '''New value''' field.<br> | ||
| + | * Note, the New value must be 26 (alpha numeric) total characters including the spaces! If in doubt check the saved log for the original battery formatting details. | ||
| + | '''[Test]''' <br> | ||
| + | '''[Save]'''<br> | ||
| + | |||
| + | Providing the value was accepted by the controller the new battery coding is complete. | ||
=== Special Notes === | === Special Notes === | ||
Revision as of 15:31, 17 February 2015
General Information: Most 2009+ Audi A4 and newer models do NOT use a separate 61-Battery Manager. In these cases battery management is a slave (subsystem) under the 19-CAN-Gateway control module. This page covers those 8T/8K/8R and newer models using a CAN Protocol 19-CAN-Gateway control module.
If the vehicle in question uses a diagnostic capable 61-Battery Regulation controller this page should apply instead:
Long Adaptation
Installation of a new battery requires the use of the [Long Adaptation-0A] function under 19-CAN-Gateway control module. Follow the onscreen instructions to enter the Part Number, Vendor, and Serial Number all as one long new value.
Prerequisites:
- New Audi Battery Installed
- Aftermarket batteries may NOT have a valid Audi Part Number, Vendor code or Serial number. Ross-Tech cannot offer assistance if the necessary information is missing.
- Key On, Engine OFF
[Select]
[19 - CAN-Gateway]
[Long Adaptation-0A]
Channel 004
[Read]
VCDS will populate instructions in the form of a pop-up balloon with the formatting. For example:
Format: NNNNNNNNNNN XXX ZZZZZZZZZZ N = Battery Part Number (11 Digits) X = Battery Vendor (3 Digits) Z = Battery Serial Number (10 Digits)
[Add to Log] Saving the original value to a log is strongly recommended.
Type the New Battery details into the New value field.
- Note, the New value must be 26 (alpha numeric) total characters including the spaces! If in doubt check the saved log for the original battery formatting details.
[Test]
[Save]
Providing the value was accepted by the controller the new battery coding is complete.