Audi A8 (4E) Brake Electronics

Login

Note #1: After Login has been carried out you need to recode the control module.
Note #2: The PR codes ( such as 1LJ ) can be found in a sticker near the spare tire well and the matching sticker on the 1st page of the owners manual (Example)

• 0?xxx: Chassis
  • 3 = Audi S8 (Short Wheel Base)
  • 5 = Audi A8 (Short Wheel Base) Fourth digit of the VIN is L
  • 6 = Audi A8 (Long Wheel Base) Fourth digit of the VIN is M
• 0x?xx: Brakes
  • 1 = 2FNR 42 AL 18" (PR-1LJ)
  • 2 = 2FNR 42 AL 17" (PR-1LL)
  • 4 = FNRG-60 16" (PR-1LG)
  • 7 = Brembo M6 AL 19" (PR-1LW)
• 0xx?x: Engine
  • 2 = 10 Cyl. Gasoline
  • 3 = 12 Cyl. Gasoline OR 6/8 Cyl. Gasoline/Diesel with Brembo M6 AL 19" (PR-1LW)
  • 5 = 6/8 Cyl. Diesel w/o Brembo M6 AL 19" (PR-1LW)
  • 6 = 6 Cyl. Diesel (Long Wheel Base)
  • 9 = 6/8 Cyl. Gasoline w/o Brembo M6 AL 19" (PR-1LW)
• 0xxx?: Transmission
  • 7 = Automatic (09E/09L)
  • 9 = Multitronic (01J)

Coding

Note #1: Coding is accepted after a specific login has been carried out.
Note #2: After successful coding the steering angle sensor basic setting needs to be carried out.
Note #3: The PR codes ( such as 1LJ ) can be found in a sticker near the spare tire well and the matching sticker on the 1st page of the owners manual (Example)

• 0?xxx: Chassis
  • 1 = Audi S8 (Short Wheel Base)
  • 7 = Audi A8 (Long Wheel Base)
  • 8 = Audi A8 (Short Wheel Base)
• 0x?xx: Brakes
  • 3 = FNRG-60 16" (PR-1LG)
  • 5 = 2FNR 42 AL 17" (PR-1LL)
  • 6 = 2FNR 42 AL 18" (PR-1LJ)
  • 7 = Brembo M6 AL 19" (PR-1LW)
• 0xx?x: Engine
  • 2 = 10 Cyl. Gasoline
  • 3 = 12 Cyl. Gasoline OR 6/8 Cyl. Gasoline/Diesel with Brembo M6 AL 19" (PR-1LW)
  • 5 = 6/8 Cyl. Diesel w/o Brembo M6 AL 19" (PR-1LW)
  • 6 = 6 Cyl. Diesel (Long Wheel Base)
  • 9 = 6/8 Cyl. Gasoline w/o Brembo M6 AL 19" (PR-1LW)
• 0xxx?: Transmission
  • 7 = Automatic (09E/09L)
  • 9 = Multitronic (01J)
    

Note: Some modules may require the coding in a 7 digit format. If the coding is rejected inset two leading zeros prior to the five digit coding. Example: Coding 08597, enter 0008597.

Basic Setting

Steering Angle Sensor (G85) Calibration

[Select]
[03 - ABS Brakes]

[Fault Codes - 02]
[Done, Go Back]

Turn steering wheel at least 30 ° left and back straight ahead.

[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]

[Login - 11]
Or [Coding - 11] if Login is not shown
Enter 40168
[Do It!]

[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]

[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]

[Close Controller, Go Back - 06]