D A N A
| Acronym (English) |
Acronym (German) |
Meaning |
|---|---|---|
| AFL | AFL | Automatic Headlamp Activation / Automatische Fahrlichteinschaltung |
| BAP | BAP | Operating and Display Protocol / Bedien- und Anzeigeprotokoll |
| CCS | GRA | Cruise Control System / Geschwindigkeitsregelanlage |
| CL | ZV | Centeral Locking / Zentralverriegelung |
| DRL | TFL | Daytime Running Light / Tagfahrlicht |
| DWA | DWA | Car Alarm / Diebstahlwarnanlage |
| ESCL | ELV | Electronic Steering Column Lock |
| ESI | WIV | Extended Service Interval (also referred to as flexible Service Interval) |
| MFA | MFA | Multi-Function display / Multifunktionsanzeige |
| MFSW | MFL | Multi-Function Steering Wheel/ Multifunktionslenkrad |
| PW | EFH | Power Windows / Elektrische Fensterheber |
| RC | FFB | Remote Control / Funkfernbedienung |
| RL | RFL | Reverse Light / Rückfahrlicht |
| RFL | NSL | Rear Fog Lamp / Nebelschlusslicht |
| SRI | SIA | Service Reminder Indicator |
| x | x | x |
7-Speed Direct Shift Gearbox (DSG/0AM)
General Information about this Transmission can be found in the Wikipedia entry. Additional information can be found in the Official Factory Repair Information.
Basic Setting
Prerequisites:
- Fluid Temperature 30°C - 60°C, see Measuring Blocks, Group??? - P my sources said 30 min.
- Selector Lever in P
- Ignition ON, Engine OFF
- Parking brake applied
- No Fault Codes stored in the TCM
-
- Brake Pedal operated (hold for the whole procedure) ?
- Throttle Pedal not operated ?
-
NOTE: Be sure to perform the following steps in the sequence shown, followed by the defined test drive.
[Select]
[02 - Transmission]
[Basic Settings - 04]
Group 060
[Go!]
[ON/OFF/Next] may be necessary
- The live data should display 4 | 0 | 0 in Basic Settings after 2 -to- 5 minutes.
- After the 4 | 0 | 0 results are displayed, start the engine immediately and allow it to idle. If 4 | 0 | 0 is not shown do NOT start the engine, something is wrong with the procedure or transmission.
- It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort the Basic Settings sequence prematurely if you hear clacking noises. This is similar to the 02E 6-Speed DSG.
- The live data should display 254 | 0 | 0 to confirm a successful Basic Settings after 3 -to- 6 minutes. (254 | 7 | 0 alone would Not be complete yet)
[Done, Go Back]
Switch off Ignition, wait 30 Seconds and switch it back on.
[Fault Codes - 02]
Check and clear any fault codes.
[Close Controller, Go Back - 06]
Perform the Defined Test Drive.
Special Procedures
Defined Test Drive
Suggested test drive after replacing the Mechatronics module/TCM or successful basic setting.
Prerequisites:
- Fluid Temperature 30...100 °C (86...210 °F), see Measuring Blocks, Group ???.
- Do Not use Cruise Control.
- Transmission fluid greater than 30* C
- With the shifter in Drive accelerate at half throttle to 2nd gear.
- Stop and repeat half throttle acceleration into 2nd gear.
- Stop followed by shifting into reverse and backing up two times.
- Stop followed by driving in each forward gear using the Tiptronic shifters for no less than 3 seconds per gear.
The next portion of the drive must be done in any group choice of the following gears to maintain the proper RPM and maintain a safe driving distance on the road:
- A = Gears 4th or 6th (4th is preferred)
- B = Gears 3rd, 5th or 7th (5th is preferred)
- Using the Tiptronic shifters maintain the range of 2,000 -to- 4,500 RPM and drive in each gear group (A and B) for no less than one full minute (two minutes are preferred). Use variable accelerator pedal positions but accelerate to full throttle at one point in each gear group during this one minute process.
- MVBs 180.1 -and- 200.1 should confirm clutch adaptations with values of 3 or greater. If any portion of the adaptation is not completed it should finish on its own with normal driving.
NOTE: If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.
Special Notes
- Some modules do not require the use if the [ON/OFF/Next] button. If an Error is displayed after clicking the button, or the Basic Settings status does not switch to On, let the selected group and procedure finish on its own.
- It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort the Basic Settings sequence prematurely if you hear clacking noises.