Audi A4 (8D) Brake Electronics (Bosch 5.3 ABS/EDS/ASR/ESP)

Login

• Notes:
  • After Login has been carried out you need to recode the Control Module.
  • Do NOT exit the Control Module in between the individual steps.
  • For Audi A8 (4D) always use 4 as Selection for Brakes.
  • The PR-Codes ( such as 1LB ) can be found in a sticker near the spare tire well.

• 0?xxx: Chassis
  • 5 = Audi A8 (4D)
  • 7 = Audi A6 (4B)
  • 9 = Audi A4 (8D) / VW Passat (3B)
• 0x?xx: Brakes
  • 3 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
  • 4 = FN2/HP2 (Dual-Piston) [PR-1LX]
  • 5 = FN3 (Teves/ATE) [PR-1LB]
  • 6 = C54 (Lucas) [PR-1LZ]
• 0xx?x: Engine
  • 5 = 4/6/8 Cyl. Diesel
  • 7 = 4/5 Cyl. Gasoline
  • 9 = 6/8/12 Cyl. Gasoline
• 0xxx?: Transmission
  • 3 = Manual with Low Range (only Audi A6 Allroad)
  • 5 = Manual
  • 7 = Automatic (01L/01N/01V)
  • 9 = Multitronic (01J)

Coding

• Notes
  • Coding is accepted after a specific login has been carried out.
  • After successful coding the Steering Angle Sensor Basic Setting needs to be carried out.
  • Do NOT exit the Control Module in between the individual steps.
  • For Audi A8 (4D) always use 3 as Selection for Brakes.
  • In some cases, you will need to enter a non-zero WSC, such as 12345-123-12345.
  • The PR-Codes ( such as 1LB ) can be found in a sticker near the spare tire well.

• 0?xxx: Chassis
  • 4 = Audi A4 (8D) / VW Passat (3B)
  • 6 = Audi A6 (4B)
  • 8 = Audi A8 (4D)
• 0x?xx: Brakes
  • 1 = C54 (Lucas) [PR-1LZ]
  • 2 = FN3 (Teves/ATE) [PR-1LB]
  • 3 = FN2/HP2 (Dual-Piston) [PR-1LX]
  • 4 = FNRG-60 (Teves/ATE) [PR-1LA/1LG]
• 0xx?x: Engine
  • 5 = 4/6/8 Cyl. Diesel
  • 7 = 4/5 Cyl. Gasoline
  • 9 = 6/8/12 Cyl. Gasoline
• 0xxx?: Transmission
  • 3 = Manual with Low Range (only Audi A6 Allroad)
  • 5 = Manual
  • 7 = Automatic (01L/01N/01V)
  • 9 = Multitronic (01J)

Basic Setting

Steering Angle Sensor (G85) Calibration

Note: Make sure the above Login and Coding have been done successfully before proceeding.

[Meas. Blocks - 08]
Group 005 Field 1 (Steering Angle Sensor -G85-)
Turn steering wheel at least 30 ° left and back straight ahead.
Specification: 0.0 °
Tolerance (when straight): ±5.0 °
[Done, Go Back]

[Login - 11]
Enter 40168
[Do It!]

[Basic Settings - 04]
Group 001
[Go!]
[Done, Go Back]

[Fault Codes - 02]
All fault codes should have disappeared.
[Done, Go Back]

[Close Controller, Go Back - 06]