VW Golf (1K) Headlight Aim Control (Xenon with AFS)

Coding

Software Part Number 5M0-907-357:

• 0000001 = VW Passat (3C) Left-Hand-Drive / Rest of World
• 0000003 = VW Eos (1F) Left-Hand-Drive / Rest of World
• 0000004 = VW Golf/Jetta (1K/5M) Left-Hand-Drive / Rest of World
• 0000005 = VW Touran (1T) Left-Hand-Drive
• 0000006 = VW Passat (3C) Right-Hand-Drive / Rest of World
• 0000007 = VW Passat (3C) Left-Hand-Drive / North America
• 0000010 = VW Eos (1F) Right-Hand-Drive / Rest of World
• 0000011 = VW Eos (1F) Left-Hand-Drive / North America
• 0000012 = VW Golf/Jetta (1K/5M) Right-Hand-Drive / Rest of World
• 0000013 = VW Golf/Jetta (1K/5M) Left-Hand-Drive / North America
• 0000014 = VW Touran (1T) Right-Hand-Drive
• 0000015 = Seat Altea/Toledo (5P) and Leon (1P) Left-Hand-Drive
• 0000016 = Seat Altea/Toledo (5P) and Leon (1P) Right-Hand-Drive

Software Part Number 5M0-907-357-A and above:

Please contact Ross-Tech or your local Distributor for Assistance with coding this Control Module. Make sure to include a full Diagnostic Protocol (VCDS > Auto-Scan) as well as Information why you need to recode this Control Module in your Request.

Adaptation

Channel 016: Tourist Solution

When driving in countries where driving is performed on the opposite side as in the native country the headlights must be changed over to avoid blinding the oncoming traffic.

• 0 = Disabled
• 1 = Enabled

Security Access

• 15284 = Adaptation Enabling

Basic Setting

Headlight Adjustment

[Select]
[55 - Xenon Range]
[Basic Settings - 04]
Group 001
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]

• The meas. block field now shows "Wait" and should switch to "Adjust Headlights" then (this may take up to 10 seconds).
• Adjust the headlights using their manual adjusting screws as referenced against a suitable aiming target.

[ON/OFF/Next]
The adjustment should now be learned.
[Done, Go Back]
Don't forget to check/clear fault codes afterwards.
[Close Controller, Go Back - 06]

Special Notes

• When fault code: 01042 - Control Module; Not Coded is stored in conjunction with one or more of the AFS lamps lacking I.D. with the text "fehlt" this fault is normal. Both Sub-system (Slave) AFS modules must be online and communicating before Coding -or- Basic Settings can be completed.

The AFS modules ( 7L6-941-329-B ) are communicating properly in this example:

Address 55: Xenon Range
  Part No SW: 5M0 907 357 C
  Component: AFS-Steuergeraet    0142  
  Coding: 1446940
 
  Part No: 7L6 941 329 B
  Component: AFS-Lst.-Modul l    0004  
  Coding: 00000022
 
  Part No: 7L6 941 329 B
  Component: AFS-Lst.-Modul r    0004  
  Coding: 00000022

The AFS modules are Not communicating properly in this example:

Address 55: Xenon Range
  Part No SW: 5M0 907 357 C
  Component: AFS-Steuergeraet    0142  
  Coding: 1446940
 
  Part No: ID-L fehlt
  Component: AFS-Lst.-Modul l    ....
  Coding: 00000255 
 
  Part No: 7L6 941 329 B
  Component: AFS-Lst.-Modul r    0004  
  Coding: 00000022

The Coding cannot be changed in the above example. The cause of the fehlt / missing messages must be corrected first. This includes Fuses, Power, Ground, Wiring Problems, and the actual AFS module(s).