Difference between revisions of "7-Speed S-Tronic Direct-Shift Gearbox (DSG/0B5)"
Line 10: | Line 10: | ||
== Basic Setting == | == Basic Setting == | ||
'''<u>Prerequisites:</u>'''<br> | '''<u>Prerequisites:</u>'''<br> | ||
+ | * Transmission fluid level correct | ||
+ | * Transmission fluid temperature between 40°C - 100°C. | ||
* TCM fault free however it is strongly recommended to check/clear all Powertrain controllers faults also.<br> | * TCM fault free however it is strongly recommended to check/clear all Powertrain controllers faults also.<br> | ||
* Key on, Engine off<br> | * Key on, Engine off<br> | ||
* Selector lever in P<br> | * Selector lever in P<br> | ||
+ | <br> | ||
+ | <u>'''All 3 Basic Setting operations need to be completed in the order listed below</u>'''<br> | ||
<br> | <br> | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
'''[02 - Auto Trans]'''<br> | '''[02 - Auto Trans]'''<br> | ||
− | '''[Basic Settings - 04]''' | + | '''[Basic Settings - 04]'''<br> |
+ | <br> | ||
+ | Select '''Erase counter for start and stop processes'''<br> | ||
+ | '''[Go!]''' to activate the Basic Setting.<br> | ||
+ | After the result of '''Finished Correctly''' or '''Not Running''' appears click '''[Stop]'''<br> | ||
+ | '''[Done, Go Back]'''<br> | ||
+ | <br> | ||
+ | Start the Engine and leave the Selector lever in Park<br> | ||
+ | <br> | ||
+ | '''[Basic Settings - 04]'''<br> | ||
+ | Select '''Clutch valve calibration''' | ||
+ | '''[Go!]''' to activate the Basic Setting.<br> | ||
+ | After the result of '''Finished Correctly''' appears click '''[Stop]'''<br> | ||
+ | <br> | ||
+ | Select '''Distance sensor calibration'''<br> | ||
+ | '''[Go!]''' to activate the Basic Setting.<br> | ||
+ | ''Clunking noises from the transmission are normal''<br> | ||
+ | After the result of '''Finished Correctly''' appears click '''[Stop]'''<br> | ||
+ | '''[Done, Go Back]'''<br> | ||
+ | |||
+ | -- Save for another phone call--<br> I'm gonna get this completed today! | ||
+ | |||
− | + | gfyuguy | |
At the present time we do not have a Basic Setting procedure on this page however the following thread in our forum can be used: | At the present time we do not have a Basic Setting procedure on this page however the following thread in our forum can be used: |
Revision as of 14:40, 7 October 2015
General Information about this Transmission can be found in the Wikipedia entry. Additional information can be found in the Official Factory Repair Information.
Coding
- When replacing this Mechatronic unit Component Protection fault code(s) may be stored.
Basic Setting
Prerequisites:
- Transmission fluid level correct
- Transmission fluid temperature between 40°C - 100°C.
- TCM fault free however it is strongly recommended to check/clear all Powertrain controllers faults also.
- Key on, Engine off
- Selector lever in P
All 3 Basic Setting operations need to be completed in the order listed below
[Select]
[02 - Auto Trans]
[Basic Settings - 04]
Select Erase counter for start and stop processes
[Go!] to activate the Basic Setting.
After the result of Finished Correctly or Not Running appears click [Stop]
[Done, Go Back]
Start the Engine and leave the Selector lever in Park
[Basic Settings - 04]
Select Clutch valve calibration
[Go!] to activate the Basic Setting.
After the result of Finished Correctly appears click [Stop]
Select Distance sensor calibration
[Go!] to activate the Basic Setting.
Clunking noises from the transmission are normal
After the result of Finished Correctly appears click [Stop]
[Done, Go Back]
-- Save for another phone call--
I'm gonna get this completed today!
gfyuguy
At the present time we do not have a Basic Setting procedure on this page however the following thread in our forum can be used: http://forums.ross-tech.com/showthread.php?2293-Audi-A4-2-0-TFSI-Quattro-s-tronic-0B5-%28DL501%29-problem&p=23158&viewfull=1#post23158
Special Notes
- Numerous Audi TPIs/TSBs exist for 0B5 transmission problems. Although a majority are flash update related some are hardware ("printed circuits"/internal wiring harness) related instead such as TPI 2022497 when P1740 - Clutch Temperature Monitoring is stored.