Difference between revisions of "7-Speed S-Tronic Direct-Shift Gearbox (DSG/0B5)"
Line 39: | Line 39: | ||
After the result of '''Finished Correctly''' appears click '''[Stop]'''<br> | After the result of '''Finished Correctly''' appears click '''[Stop]'''<br> | ||
'''[Done, Go Back]'''<br> | '''[Done, Go Back]'''<br> | ||
− | + | <br> | |
− | + | Switch off Ignition, wait 10 Seconds and switch it back on.<br> | |
− | + | '''[Fault Codes - 02]'''<br> | |
− | + | Check and clear any fault codes<br> | |
− | + | '''[Close Controller, Go Back - 06]'''<br> | |
− | + | Perform a test drive and check for fault codes again after doing so.<br><br> | |
− | |||
− | |||
− | |||
− | - | ||
− | |||
==== Special Notes ==== | ==== Special Notes ==== | ||
* Numerous Audi TPIs/TSBs exist for 0B5 transmission problems. Although a majority are flash update related some are hardware ("printed circuits"/''internal wiring harness'') related instead such as TPI 2022497 when [[18148/P1740/005952 | P1740 - Clutch Temperature Monitoring]] is stored. | * Numerous Audi TPIs/TSBs exist for 0B5 transmission problems. Although a majority are flash update related some are hardware ("printed circuits"/''internal wiring harness'') related instead such as TPI 2022497 when [[18148/P1740/005952 | P1740 - Clutch Temperature Monitoring]] is stored. | ||
− | + | <font color=white>forums.ross-tech.com/showthread.php?2293-Audi-A4-2-0-TFSI-Quattro-s-tronic-0B5-%28DL501%29-problem&p=23158&viewfull=1#post23158</font> | |
[[Category:Transmissions]] | [[Category:Transmissions]] |
Revision as of 18:06, 7 October 2015
General Information about this Transmission can be found in the Wikipedia entry. Additional information can be found in the Official Factory Repair Information.
Coding
- When replacing this Mechatronic unit Component Protection fault code(s) may be stored.
Basic Setting
Prerequisites:
- Transmission fluid level correct
- Transmission fluid temperature between 40°C - 100°C.
- TCM fault free however it is strongly recommended to check/clear all Powertrain controllers faults also.
- Key on, Engine off
- Selector lever in P
All 3 Basic Setting operations need to be completed in the order listed below
[Select]
[02 - Auto Trans]
[Basic Settings - 04]
Select Erase counter for start and stop processes
[Go!] to activate the Basic Setting.
After the result of Finished Correctly or Not Running appears click [Stop]
[Done, Go Back]
Start the Engine and leave the Selector lever in Park
[Basic Settings - 04]
Select Clutch valve calibration
[Go!] to activate the Basic Setting.
After the result of Finished Correctly appears click [Stop]
Select Distance sensor calibration
[Go!] to activate the Basic Setting.
Clunking noises from the transmission are normal
After the result of Finished Correctly appears click [Stop]
[Done, Go Back]
Switch off Ignition, wait 10 Seconds and switch it back on.
[Fault Codes - 02]
Check and clear any fault codes
[Close Controller, Go Back - 06]
Perform a test drive and check for fault codes again after doing so.
Special Notes
- Numerous Audi TPIs/TSBs exist for 0B5 transmission problems. Although a majority are flash update related some are hardware ("printed circuits"/internal wiring harness) related instead such as TPI 2022497 when P1740 - Clutch Temperature Monitoring is stored.
forums.ross-tech.com/showthread.php?2293-Audi-A4-2-0-TFSI-Quattro-s-tronic-0B5-%28DL501%29-problem&p=23158&viewfull=1#post23158