Difference between revisions of "Readiness - APB Engine Code"
From Ross-Tech Wiki
| Line 1: | Line 1: | ||
| − | + | === Defined Test Drive === | |
| + | |||
| + | '''<u>Prerequisites:</u>''' | ||
| + | * Ignition ON and Engine ON. | ||
| + | * No Fault Codes stored. | ||
| + | * Transmission Oil Temperature must be between 60 °C and 90 °C. | ||
| + | ** If the procedure does not succeed in the first try, make sure the temperature is above 80 °C. | ||
| + | * All driving and braking has to be done in partial load, avoid full throttle/braking! | ||
| + | * Normally the adaptation needs to be carried out when: | ||
| + | ** Transmission Control Module has been recoded | ||
| + | ** Input Shaft has been replaced | ||
| + | ** Hydraulic Unit has been replaced | ||
| + | ** Transmission Control Module has been replaced | ||
| + | ** Transmission has been replaced | ||
| + | |||
| + | |||
| + | '''[Select]'''<br> | ||
| + | '''[02 - Transmission]'''<br> | ||
| + | '''[Adaptation - 10]'''<br> | ||
| + | Channel 000<br> | ||
| + | '''[Read]'''<br> | ||
| + | '''[Save]'''<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | '''[Measuring Blocks - 08]'''<br> | ||
| + | Block 010 (in 1st Row)<br> | ||
| + | Block 011 (in 2nd Row)<br> | ||
| + | '''[Go!]'''<br> | ||
| + | Check fields 2, specification is '''ADP OK'''.<br> | ||
| + | * Move the selector lever in position '''D''' and drive with partial load '''20 m / 70 ft''' forward, then brake to standstill. | ||
| + | * Hold the brake for 10 seconds. | ||
| + | * Move the selector lever in position '''R''' and drive with partial load '''20 m / 70 ft''' reverse, then brake to standstill. | ||
| + | * Hold the brake for 10 seconds. | ||
| + | The procedure needs to be repeated at least 5 times and can be repeated up to 10 times until the measuring values show '''ADP OK'''.<br> | ||
| + | '''[Done, Go Back]'''<br> | ||
| + | '''[Close Controller, Go Back - 06]'''<br><br> | ||
Revision as of 15:00, 5 October 2006
Defined Test Drive
Prerequisites:
- Ignition ON and Engine ON.
- No Fault Codes stored.
- Transmission Oil Temperature must be between 60 °C and 90 °C.
- If the procedure does not succeed in the first try, make sure the temperature is above 80 °C.
- All driving and braking has to be done in partial load, avoid full throttle/braking!
- Normally the adaptation needs to be carried out when:
- Transmission Control Module has been recoded
- Input Shaft has been replaced
- Hydraulic Unit has been replaced
- Transmission Control Module has been replaced
- Transmission has been replaced
[Select]
[02 - Transmission]
[Adaptation - 10]
Channel 000
[Read]
[Save]
[Done, Go Back]
[Measuring Blocks - 08]
Block 010 (in 1st Row)
Block 011 (in 2nd Row)
[Go!]
Check fields 2, specification is ADP OK.
- Move the selector lever in position D and drive with partial load 20 m / 70 ft forward, then brake to standstill.
- Hold the brake for 10 seconds.
- Move the selector lever in position R and drive with partial load 20 m / 70 ft reverse, then brake to standstill.
- Hold the brake for 10 seconds.
The procedure needs to be repeated at least 5 times and can be repeated up to 10 times until the measuring values show ADP OK.
[Done, Go Back]
[Close Controller, Go Back - 06]