Difference between revisions of "Readiness - APB Engine Code-without-MB"

From Ross-Tech Wiki
 
Line 18: Line 18:
 
''Throttle Body Alignment''<br>
 
''Throttle Body Alignment''<br>
  
'''[Measuring Blocks - 08]'''<br>
+
'''[Basic Settings - 04]'''<br>
 
Select group 060<br>
 
Select group 060<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
 
 
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
 
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
'''[Switch to Meas. Blocks]'''<br>
 
  
  
Line 30: Line 28:
 
Select group 063<br>
 
Select group 063<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
 
 
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
 
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.<br>
'''[Switch to Meas. Blocks]'''<br>
 
  
  
Line 47: Line 43:
 
'''[Select]'''<br>
 
'''[Select]'''<br>
 
'''[01 - Engine]'''<br>
 
'''[01 - Engine]'''<br>
'''[Measuring Blocks - 08]'''<br>
+
'''[Basic Settings - 04]'''<br>
 
Select group 071<br>
 
Select group 071<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until the fourth field reads Syst.OK<br>
Leave it in Basic Settings until the fourth field reads Syst.OK<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
  
  
Line 59: Line 53:
 
Select group 070<br>
 
Select group 070<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until the fourth field reads EVAP OK<br>
Leave it in Basic Settings until the fourth field reads EVAP OK<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
  
  
Line 68: Line 60:
 
Select group 107<br>
 
Select group 107<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until the fourth field reads Syst.OK<br>
Leave it in Basic Settings until the fourth field reads Syst.OK<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
  
  
Line 82: Line 72:
 
Select group 041<br>
 
Select group 041<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until there are kOhm readings in the first and third fields<br>
Leave it in Basic Settings until there are kOhm readings in the first and third fields<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
 
Select group 042<br>
 
Select group 042<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until there are kOhm readings in the first and third fields<br>
Leave it in Basic Settings until there are kOhm readings in the first and third fields<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
  
  
Line 101: Line 87:
 
Select group 036<br>
 
Select group 036<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until you see B1-S2 OK in the first field and B2-S2 OK in the third field<br>
Leave it in Basic Settings until you see B1-S2 OK in the first field and B2-S2 OK in the third field<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
  
  
Line 115: Line 99:
 
Select group 034<br>
 
Select group 034<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until the fourth field reads B1-S1 OK<br>
Leave it in Basic Settings until the fourth field reads B1-S1 OK<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
 
Select group 035<br>
 
Select group 035<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until the fourth field reads B2-S1 OK<br>
Leave it in Basic Settings until the fourth field reads B2-S1 OK<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
  
  
Line 134: Line 114:
 
Select group 037<br>
 
Select group 037<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until the fourth field reads Syst. OK<br>
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
 
Select group 038<br>
 
Select group 038<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until the fourth field reads Syst. OK<br>
Leave it in Basic Settings until the fourth field reads Syst. OK<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
  
  
Line 149: Line 125:
 
Select group 043<br>
 
Select group 043<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
+
Leave it in this group until the fourth field reads B1-S2 OK<br>
Leave it in Basic Settings until the fourth field reads B1-S2 OK<br>
 
'''[Switch to Meas. Blocks]'''<br>
 
 
Select group 044<br>
 
Select group 044<br>
 
'''[Go]'''<br>
 
'''[Go]'''<br>
'''[Switch to basic settings]'''<br>
 
 
Leave it in Basic Settings until the fourth field reads B2-S2 OK<br>
 
Leave it in Basic Settings until the fourth field reads B2-S2 OK<br>
'''[Switch to Meas. Blocks]'''<br>
 
  
  

Revision as of 09:16, 6 October 2006

Manually Generating Readiness

  • Ignition ON and Engine OFF


Reading and clearing fault codes

[Select]
[01 - Engine]
[Fault Codes - 02]
[Clear Codes -05]
[Done, Go Back]


Throttle Body Alignment

[Basic Settings - 04]
Select group 060
[Go]
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.


Transmission kickdown (applies to Auto Trans vehicles only!)

Select group 063
[Go]
Once you do this you will see the top right display say ADP RUN. Leave it in Basic Settings until the fourth field reads ADP OK.


[Done, Go Back]
[Close Controller, Go Back]


  • Ignition ON and Engine ON at idle


Fuel leakage test

[Select]
[01 - Engine]
[Basic Settings - 04]
Select group 071
[Go]
Leave it in this group until the fourth field reads Syst.OK


Evap purge test

Select group 070
[Go]
Leave it in this group until the fourth field reads EVAP OK


A/F control test

Select group 107
[Go]
Leave it in this group until the fourth field reads Syst.OK


  • Ignition ON and Engine ON between 1800 and 2200 rpm


O2 sensor heater test

Select group 041
[Go]
Leave it in this group until there are kOhm readings in the first and third fields
Select group 042
[Go]
Leave it in this group until there are kOhm readings in the first and third fields


  • Ignition ON and Engine ON at idle


Post-cat O2 sensors readiness test

Select group 036
[Go]
Leave it in this group until you see B1-S2 OK in the first field and B2-S2 OK in the third field


  • Ignition ON and Engine ON between 1520 and 2280 rpm


Pre-cat O2 sensors response time test

Select group 034
[Go]
Leave it in this group until the fourth field reads B1-S1 OK
Select group 035
[Go]
Leave it in this group until the fourth field reads B2-S1 OK


  • Ignition ON and Engine ON at idle


O2 sensor control test

Select group 037
[Go]
Leave it in this group until the fourth field reads Syst. OK
Select group 038
[Go]
Leave it in this group until the fourth field reads Syst. OK


Post-cat O2 sensor aging test

Select group 043
[Go]
Leave it in this group until the fourth field reads B1-S2 OK
Select group 044
[Go]
Leave it in Basic Settings until the fourth field reads B2-S2 OK


  • Ignition ON and Engine ON between 1880 and 2280 rpm


Catalytic converter test

Select group 046
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads CAT B1 OK
[Switch to Meas. Blocks]
Select group 047
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads CAT B2 OK
[Switch to Meas. Blocks]


  • Ignition ON and Engine ON at idle


Secondary air injection test (applies to Auto Trans vehicles only!)

Select group 077
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads Syst. OK
[Switch to Meas. Blocks]
Select group 078
[Go]
[Switch to basic settings]
Leave it in Basic Settings until the fourth field reads Syst. OK
[Switch to Meas. Blocks]
[Done, Go Back]


Checking Readiness
[Readiness]
Make sure none of the fields say Failed or Incomplete
[Done, Go Back]
[Close Controller, Go Back]


You're done!