Audi A5 (8T) Active Steering: Difference between revisions
From Ross-Tech Wiki
Table Of Contents
- 1. Coding
- 2. Security Access
- 3. Basic Setting
No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
__FORCETOC__ | |||
This page applies to Address '''1B-Active Steering''' in Audi models such as the '''A4''' ''(8K)'', '''A5''' ''(8T)'', '''Q5''' ''(8R)'' in addition to the newer '''A6/A7/A8''' ''(4G/4H)'' models with J792 Component: '''DYNAMIKLENK'''. <br> | |||
Active/Dynamic Steering is NOT standard equipment in all of the models listed above. This equipment can be identified using [[Production Codes (PR-Codes) can be found on the Vehicle Data Label |PR Codes]] such as 1N7 - Dynamic steering or by evaluating the data in the Auto-Scan: | |||
Address 1B: Active Steering (J792) | |||
Part No SW: 4H0 907 144 C HW: 4H0 907 144 C | |||
Component: '''DYNAMIKLENK'''. H06 0100 | |||
Address 1B: Active Steering (J792) | |||
Part No SW: 8K0 907 144 A HW: 8K0 907 144 A | |||
Component: '''DYNAMIKLENK'''. H05 0322 | |||
== Coding == | == Coding == | ||
'''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module. | '''Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module.''' A Security Access code is required prior to Coding. | ||
== Security Access == | |||
* 61378 Coding and Basic Setting enabling | |||
== Basic Setting == | == Basic Setting == | ||
'''<u>Prerequisites:</u>'''<br> | '''<u>Prerequisites:</u>'''<br> | ||
* Battery Voltage | * Battery Voltage is 12.0V or more<br> | ||
* Vehicle speed is 0 km/h<br> | |||
* No fault codes other than [[01087 | 01087 - Basic Setting Not Performed]]'''<br> | * No fault codes other than [[01087 | 01087 - Basic Setting Not Performed]]'''<br> | ||
* Perform G85-Steering Angle Sensor Basic Settings. One the following pages would apply: | |||
* Perform G85-Steering Angle Sensor Basic Settings | ** [[Audi A5 (8T) Steering Wheel Electronics#Basic Setting| 2008+ A4, A5 and Q5 Steering Angle Sensor (G85) Calibration]] | ||
** [[Audi A6 (4G) Steering Wheel Electronics#Basic Setting|2011+ A6, A7 and A8 Steering Angle Sensor (G85) Calibration]] | |||
<span style="color:#000000; background:#FFFF00"> '''Continue Only after successfully completing the G85 basic settings above''' </span> | |||
*Leave the steering wheel in the straight ahead position during the next steps (Tolerance: ±1.5 °). | |||
<span style="color:#000000; background:#FFFF00"> ''' | |||
*Leave the steering wheel in the straight ahead position during the next steps. | |||
'''[Select]'''<br> | '''[Select]'''<br> | ||
'''[1B-Active Steering]'''<br> | '''[1B-Active Steering]'''<br> | ||
'''[Security Access - 16]'''<br> | '''[Security Access - 16]'''<br> | ||
Enter 61378, to enable the basic setting.'''<br> | Enter 61378, to enable the basic setting.'''<br> | ||
'''[Do it!]'''<br> | '''[Do it!]'''<br> | ||
'''[Basic Settings - 04]'''<br> | '''[Basic Settings - 04]'''<br> | ||
| Line 41: | Line 40: | ||
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
'''[ON/OFF/Next]''' <br> | '''[ON/OFF/Next]''' <br> | ||
* Basic Settings is active. | |||
* | ** If "No Value" is shown in the 4th field turn the steering wheel at a rate lower than 50°/s in excess of 45° using both directions until OK is shown. | ||
** If "OK" was shown in the 4th field continue. | |||
'''[ON/OFF/Next]''' <br> | |||
'''[Done, Go Back]''' <br> | '''[Done, Go Back]''' <br> | ||
'''[Fault Codes - 02]'''<br> | '''[Fault Codes - 02]'''<br> | ||
| Line 50: | Line 49: | ||
'''[Close Controller, Go Back - 06]'''<br> | '''[Close Controller, Go Back - 06]'''<br> | ||
< | |||
<br> | |||
<br> | |||
Internal use reference: FS#745 | |||
Revision as of 00:13, 2 April 2016
This page applies to Address 1B-Active Steering in Audi models such as the A4 (8K), A5 (8T), Q5 (8R) in addition to the newer A6/A7/A8 (4G/4H) models with J792 Component: DYNAMIKLENK.
Active/Dynamic Steering is NOT standard equipment in all of the models listed above. This equipment can be identified using PR Codes such as 1N7 - Dynamic steering or by evaluating the data in the Auto-Scan:
Address 1B: Active Steering (J792) Part No SW: 4H0 907 144 C HW: 4H0 907 144 C Component: DYNAMIKLENK. H06 0100
Address 1B: Active Steering (J792) Part No SW: 8K0 907 144 A HW: 8K0 907 144 A Component: DYNAMIKLENK. H05 0322
Coding
Coding for this Control Module is normally done via Software Version Management (SVM). If the old Control Module is still accessible read/copy it's Coding to the new Module. A Security Access code is required prior to Coding.
Security Access
- 61378 Coding and Basic Setting enabling
Basic Setting
Prerequisites:
- Battery Voltage is 12.0V or more
- Vehicle speed is 0 km/h
- No fault codes other than 01087 - Basic Setting Not Performed
- Perform G85-Steering Angle Sensor Basic Settings. One the following pages would apply:
Continue Only after successfully completing the G85 basic settings above
- Leave the steering wheel in the straight ahead position during the next steps (Tolerance: ±1.5 °).
[Select]
[1B-Active Steering]
[Security Access - 16]
Enter 61378, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 101
[Go!]
[ON/OFF/Next]
- Basic Settings is active.
- If "No Value" is shown in the 4th field turn the steering wheel at a rate lower than 50°/s in excess of 45° using both directions until OK is shown.
- If "OK" was shown in the 4th field continue.
[ON/OFF/Next]
[Done, Go Back]
[Fault Codes - 02]
Check and clear fault codes.
[Close Controller, Go Back - 06]
Internal use reference: FS#745
No categories.