Difference between revisions of "Immobilizer III Key Matching (Cluster)"
From Ross-Tech Wiki
| (35 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
__FORCETOC__ | __FORCETOC__ | ||
| − | This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with Immobilizer III. | + | '''This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer III, where the immobilizer control module is integrated in the instrument cluster. See the seperate instructions for models where the [[Immobilizer III Key Matching (Box)|immobilizer control module is integrated in a separate immo box]] or where the [[Immobilizer III Key Matching (Kessy)|immobilizer control module is integrated in kessy]] (Keyless Entry and Start SYstem).''' |
| + | |||
== Determining IMMO-ID & VIN == | == Determining IMMO-ID & VIN == | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
| − | '''[17 - Instruments | + | '''[17 - Instruments]'''<br> |
| − | + | Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.<br> | |
| − | Look at the first "Extra" field | ||
| − | |||
| − | |||
| − | |||
'''[Close Controller, Go Back - 06]'''<br> | '''[Close Controller, Go Back - 06]'''<br> | ||
| Line 16: | Line 13: | ||
'''[Select]'''<br> | '''[Select]'''<br> | ||
| − | '''[ | + | '''[17 - Instruments]'''<br> |
'''[Meas. Blocks - 08]'''<br> | '''[Meas. Blocks - 08]'''<br> | ||
Select Block 081.<br> | Select Block 081.<br> | ||
| Line 28: | Line 25: | ||
'''<u>Prerequisites:</u>'''<br> | '''<u>Prerequisites:</u>'''<br> | ||
| + | * All keys are either new or were adapted to this car (IMMO-ID) before.<br> | ||
| + | * You can match up to 8 keys. | ||
* While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.'' | * While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). ''The passenger seat is an adequate place.'' | ||
* Battery voltage at least 12.5 V.<br> | * Battery voltage at least 12.5 V.<br> | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
'''[Select]'''<br> | '''[Select]'''<br> | ||
| − | '''[ | + | '''[17 - Instruments]'''<br> |
'''[Meas. Blocks - 08]'''<br> | '''[Meas. Blocks - 08]'''<br> | ||
| − | Select Block | + | Select Block 022.<br> |
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br> | ''The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.''<br> | ||
| Line 129: | Line 40: | ||
| − | Select Block | + | Select Block 024.<br> |
'''[Go!]'''<br> | '''[Go!]'''<br> | ||
''Make sure the shown lock times in field 1, 2 and 3 are '''0''' (each field represents a time in minutes).''<br> | ''Make sure the shown lock times in field 1, 2 and 3 are '''0''' (each field represents a time in minutes).''<br> | ||
| Line 138: | Line 49: | ||
| − | '''[ | + | '''[Login - 11]'''<br> |
| − | |||
* '''4-digit PIN''' | * '''4-digit PIN''' | ||
** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.'' | ** Enter zero followed by the 4-digit PIN. ''For example, if your PIN is 1234, enter 01234.'' | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
'''[Do it!]'''<br> | '''[Do it!]'''<br> | ||
'''[Adaptation - 10]'''<br> | '''[Adaptation - 10]'''<br> | ||
| − | Enter | + | Enter 21 in "Channel Number".<br> |
'''[Read]'''<br> | '''[Read]'''<br> | ||
''The "Stored Value" is the number of keys currently matched.''<br> | ''The "Stored Value" is the number of keys currently matched.''<br> | ||
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br> | Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.<br> | ||
| − | '' | + | ''Any old keys are automatically being cleared. All keys, including existing keys, must be matched at the same time.''<br> |
'''[Save]'''<br> | '''[Save]'''<br> | ||
| − | |||
| − | |||
| + | * ''Repeat the following steps until all Keys have been matched:'' | ||
| + | **''Switch Ignition OFF and remove Key.'' | ||
| + | **''Insert the next Key and switch Ignition ON.'' | ||
| + | **''The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out, indicating that the key has been matched.'' | ||
| + | |||
| + | '''Note:''' ''The above steps must be completed within 60 seconds after saving the Adaptation!'' | ||
| + | |||
| + | '''[Done, Go Back]'''<br> | ||
| + | '''[Close Controller, Go Back - 06]'''<br> | ||
| + | |||
| + | == Video Link == | ||
| + | === Immobilizer Gen 2 and 3 Key Adaptation === | ||
| − | + | [[File:Immobolizer.jpg|200px|link=http://www.youtube.com/watch?v=Wj3K04eMV7w]] | |
| − | |||
| − | |||
| − | |||
| − | + | http://www.youtube.com/watch?v=Wj3K04eMV7w | |
Latest revision as of 13:32, 8 April 2024
This procedure details how to match new keys to VW/Audi/Seat/Skoda vehicles with with Immobilizer III, where the immobilizer control module is integrated in the instrument cluster. See the seperate instructions for models where the immobilizer control module is integrated in a separate immo box or where the immobilizer control module is integrated in kessy (Keyless Entry and Start SYstem).
Determining IMMO-ID & VIN
[Select]
[17 - Instruments]
Look at the first "Extra" field. The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID.
[Close Controller, Go Back - 06]
---OR---
[Select]
[17 - Instruments]
[Meas. Blocks - 08]
Select Block 081.
[Go!]
The first 17-digit string is the VIN. The second 14-digit string in the Immo-ID..
[Done, Go Back]
[Close Controller, Go Back - 06]
Key Matching
Prerequisites:
- All keys are either new or were adapted to this car (IMMO-ID) before.
- You can match up to 8 keys.
- While adapting each key, make sure to place the other keys away from the ignition lock (reader coil). The passenger seat is an adequate place.
- Battery voltage at least 12.5 V.
[Select]
[17 - Instruments]
[Meas. Blocks - 08]
Select Block 022.
[Go!]
The value in field 3 must be 1. If value is not 1, the key is not capable of being adapted to Immobilizer.
You can check each key in this manner.
Select Block 024.
[Go!]
Make sure the shown lock times in field 1, 2 and 3 are 0 (each field represents a time in minutes).
- If the lock times are NOT 0:
- Do NOT switch off the ignition!
- Allow the car to sit for AT LEAST the number of minutes that were indicated by the fields 1-3.
[Done, Go Back]
[Login - 11]
- 4-digit PIN
- Enter zero followed by the 4-digit PIN. For example, if your PIN is 1234, enter 01234.
[Do it!]
[Adaptation - 10]
Enter 21 in "Channel Number".
[Read]
The "Stored Value" is the number of keys currently matched.
Enter a "new value" corresponding to the total number of keys to be matched, including any existing keys.
Any old keys are automatically being cleared. All keys, including existing keys, must be matched at the same time.
[Save]
- Repeat the following steps until all Keys have been matched:
- Switch Ignition OFF and remove Key.
- Insert the next Key and switch Ignition ON.
- The Immobilizer Warning Light will light up for ~2 seconds, wait until it goes out, indicating that the key has been matched.
Note: The above steps must be completed within 60 seconds after saving the Adaptation!
[Done, Go Back]
[Close Controller, Go Back - 06]
Video Link
Immobilizer Gen 2 and 3 Key Adaptation
