Difference between revisions of "Audi A6 (4B) Level Control (4-Wheel)"

From Ross-Tech Wiki
 
Line 17: Line 17:
 
=== Suspension Level Control Calibration ===
 
=== Suspension Level Control Calibration ===
  
−
* ''See How-To: [http://www.ross-tech.com/vag-com/cars/levelcontrol.html Suspension Level Control Calibration]''
+
'''Prerequisites'''
−
 
+
* Engine at idle
−
Before starting the procedure, measure and write down the height of each corner of the vehicle. Measure between the center of the wheel (the space in between the center two rings of the Audi logo) and the lower edge of the fender. All measurements have to be done in Millimeters (mm). A diagram is shown here: [http://ross-tech.com/vag-com/cars/images/rim.jpeg] <br>
+
* Transmission in park/neutral
−
 
+
* Doors, hood, rear lid or hatch are to remain shut during the entire procedure
−
'''<u>Prerequisites:</u>'''<br>
 
−
* Transmission in park/neutral.
 
−
* Start the vehicle, keep the engine running and do not switch off the ignition.
 
−
* Doors have to stay closed, otherwise the system is not ready.
 
  
 
'''[Select]'''<br>
 
'''[Select]'''<br>
 
'''[34 - Level Control]'''<br>
 
'''[34 - Level Control]'''<br>
−
 
 
'''[Login - 11]'''<br>
 
'''[Login - 11]'''<br>
−
Enter 31564<br>
+
* Enter 31564
 
'''[Do It!]'''<br>
 
'''[Do It!]'''<br>
 +
'''[Adaption - 10]'''<br>
 +
* Channel 01
 +
'''[Read]'''<br>
  
−
'''[Adaptation - 10]'''<br>
+
The vehicle will now try to level itself. The first field will show "Wait". Once this process is complete, the first field will show "Value".<br>
−
Use the '''[Up]''' button to scroll up to channel 01. The suspension should automatically adjust its ride height to level 2 for calibration. After the suspension has finished adjusting, each of the four boxes at the top of the Adaptation screen should show "N/A".
+
Now measure the ride height, in millimeters, from the center of the wheel to the edge of fender, do this for all four wheels and record the values.<br>
−
 
+
https://www.ross-tech.com/vag-com/cars/images/rim.jpeg
−
'''<u>Channel 01: Left Front</u>'''
 
−
 
 
−
In the '''New Value''' field, enter the measurement from the LEFT FRONT corner in millimeters.
 
−
 
 
−
'''[Test]''' Make sure that Test Value shows the number you just entered and click '''[Save]'''<br>
 
−
 
 
−
On the confirmation screen, make sure that you are saving the value in millimeters for the LEFT FRONT corner to channel 01 and click '''[Yes]'''<br>
 
−
 
 
−
'''<u>Channel 02: Right Front</u>'''
 
−
 
 
−
Use the '''[Up]''' button to scroll up to channel 02.<br>
 
−
 
 
−
In the '''New Value''' field, enter the measurement from the RIGHT FRONT corner in millimeters.
 
−
 
 
−
'''[Test]''' Make sure that Test Value shows the number you just entered and click '''[Save]'''<br>
 
−
 
 
−
On the confirmation screen, make sure that you are saving the value in millimeters for the RIGHT FRONT corner to channel 02 and click '''[Yes]'''<br>
 
−
 
 
−
'''<u>Channel 03: Left Rear</u>'''
 
−
 
 
−
Use the '''[Up]''' button to scroll up to channel 03.<br>
 
  
−
In the '''New Value''' field, enter the measurement from the LEFT REAR corner in millimeters.
+
<br>
  
−
'''[Test]''' Make sure that Test Value shows the number you just entered and click '''[Save]'''<br>
+
In the "New Value" field for '''channel 01''', input the measurement from the '''left front''' wheel.<br>
 +
'''[Test]''' - '''[Save]''' - Confirm '''[Yes]'''<br>
 +
Click the '''[Up]''' button to go to Channel 02.<br>
  
−
On the confirmation screen, make sure that you are saving the value in millimeters for the LEFT REAR corner to channel 03 and click '''[Yes]'''<br>
 
  
−
'''<u>Channel 04: Right Rear</u>'''
+
In the "New Value" field for '''channel 02''', input the measurement from the '''right front''' wheel.<br>
 +
'''[Test]''' - '''[Save]''' - Confirm '''[Yes]'''<br>
 +
Click the '''[Up]''' button to go to Channel 03.<br>
  
−
Use the '''[Up]''' button to scroll up to channel 04.<br>
 
  
−
In the '''New Value''' field, enter the measurement from the RIGHT REAR corner in millimeters.
+
In the "New Value" field for '''channel 03''', input the measurement from the '''left rear wheel'''.<br>
 +
'''[Test]''' - '''[Save]''' - Confirm '''[Yes]'''<br>
 +
Click the '''[Up]''' button to go to Channel 04.<br>
  
−
'''[Test]''' Make sure that Test Value shows the number you just entered and click '''[Save]'''<br>
 
  
−
On the confirmation screen, make sure that you are saving the value in millimeters for the RIGHT REAR corner to channel 04 and click '''[Yes]'''<br>
+
In the "New Value" field for '''channel 04''', input the measurement from the '''right rear wheel'''.<br>
 +
'''[Test]''' - '''[Save]''' - Confirm '''[Yes]'''<br>
 +
Click the '''[Up]''' button to go to Channel 05.<br>
  
−
'''<u>Channel 05: Saving settings</u>'''
 
  
−
Use the '''[Up]''' button to scroll up to channel 05.<br>
+
In the "New Value" field for '''channel 05''', input a value of '''1'''.<br>
 +
'''[Test]''' - '''[Save]''' - Confirm '''[Yes]'''<br>
  
−
In the '''New Value''' field, enter a value of "01". '''[Test]''' Make sure that Test Value shows 01 and click '''[Save]'''<br>
+
'''[Done, Go Back]'''<br>
  
 +
Check for fault codes, if all procedures went fine there should be none.<br>
 
=== Video Link ===
 
=== Video Link ===
  

Latest revision as of 10:25, 31 July 2024

Coding

  • 25500 = Standard


Security Access

Adaptation

Basic Setting

The Basic Setting function is not supported by this module,

Special Procedures

Suspension Level Control Calibration

Prerequisites

  • Engine at idle
  • Transmission in park/neutral
  • Doors, hood, rear lid or hatch are to remain shut during the entire procedure

[Select]
[34 - Level Control]
[Login - 11]

  • Enter 31564

[Do It!]
[Adaption - 10]

  • Channel 01

[Read]

The vehicle will now try to level itself. The first field will show "Wait". Once this process is complete, the first field will show "Value".
Now measure the ride height, in millimeters, from the center of the wheel to the edge of fender, do this for all four wheels and record the values.
rim.jpeg


In the "New Value" field for channel 01, input the measurement from the left front wheel.
[Test] - [Save] - Confirm [Yes]
Click the [Up] button to go to Channel 02.


In the "New Value" field for channel 02, input the measurement from the right front wheel.
[Test] - [Save] - Confirm [Yes]
Click the [Up] button to go to Channel 03.


In the "New Value" field for channel 03, input the measurement from the left rear wheel.
[Test] - [Save] - Confirm [Yes]
Click the [Up] button to go to Channel 04.


In the "New Value" field for channel 04, input the measurement from the right rear wheel.
[Test] - [Save] - Confirm [Yes]
Click the [Up] button to go to Channel 05.


In the "New Value" field for channel 05, input a value of 1.
[Test] - [Save] - Confirm [Yes]

[Done, Go Back]

Check for fault codes, if all procedures went fine there should be none.

Video Link

Suspension Leveling Calibration

Thumbnail.jpg

http://www.youtube.com/watch?v=o2aeQ6bhu-Y

Retrieved from "http://wiki.ross-tech.com/wiki/index.php?title=Audi_A6_(4B)_Level_Control_(4-Wheel)&oldid=9584"