Difference between revisions of "Xenon Basic Settings in BCM1/09-Cent. Elect. (J519) controller"
(Created page with "This page is under construction. This page will only apply to vehicles with factory installed Xenon headlights that do NOT use a diagnostic capable 55-Xenon Range control mod...") |
|||
Line 1: | Line 1: | ||
− | + | __FORCETOC__ | |
+ | '''General Information'''<br> | ||
− | + | This page applies to vehicles with factory installed Xenon headlights that do '''NOT''' use a diagnostic capable 55-Headlight Range control module. If the vehicle in question has a diagnostic capable 55-Headlight Range control module please use the applicable Ross-Tech Wiki [[Diagnostic Procedures|Diagnostic Procedure]] page for that system. | |
+ | * Registered VCDS users encountering difficulty determining which type of '''factory installed''' Xenon headlight system is installed can: | ||
+ | ** Join and post the complete VCDS Auto-Scan in the [http://forums.ross-tech.com/forumdisplay.php?9-Car-Repair-Support Car Repair Support] section of our [http://forums.ross-tech.com forum]. | ||
+ | ** Send the complete VCDS Auto-Scan directly via [mailto:Support@Ross-Tech.com email]. | ||
+ | |||
+ | * Registered VCDS users encountering difficulty [[Retrofitting]] a Xenon headlight system need to join and post in the [http://forums.ross-tech.com/forumdisplay.php?10-Retrofits Retrofits] section of our [http://forums.ross-tech.com forum]. Post the Auto-Scan prior to the retrofit in addition to the Auto-Scan after the replacement parts were installed when assistance is needed. | ||
+ | <br> | ||
+ | |||
+ | As of VCDS Release 15.7.0 it is possible to perform Basic Settings in address 09-Cent. Elect. This procedure has received limited feedback to date so Paul's [http://www.a5oc.com/forums/audi-a5-s5-tech/97369-new-xenon-range-adjustment.html New Xenon Range Adjustment Procedure - HOW TO] thread may be helpful.<br> | ||
+ | |||
+ | |||
+ | ---- | ||
+ | == Basic Setting == | ||
+ | === Headlight Adjustment === | ||
+ | '''<u>Prerequisites:</u>'''<br> | ||
+ | * Vehicle on Level ground. | ||
+ | * Headlights, suspension leveling components and similar fully assembled and in proper working order. | ||
+ | * Address 09-Cent. Elect (BCM1) fault free with the exception of [[01539]], [[02658]], and [[02659]]. | ||
+ | * Headlight switch ON (not Auto''matic'' mode): | ||
+ | |||
+ | '''[Select]'''<br> | ||
+ | '''[09 - Cent. Elect.]'''<br> | ||
+ | '''[Basic Settings - 04]'''<br> | ||
+ | Group 011<br> | ||
+ | '''[Go!]'''<br> | ||
+ | * The meas. block field shows [''Reg. Position'' | ''Learned'' | ''0.0'' | ''N/A''] | ||
+ | Activate the Basic Setting.<br> | ||
+ | '''[ON/OFF/Next]'''<br> | ||
+ | * The meas. block field now shows [''Adjust'' | ''Headlights'' | ''not available'' | ''N/A''] | ||
+ | * Adjust the headlights (if needed) using their manual adjusting screws as referenced against a suitable aiming target. | ||
+ | Deactivate the Basic Setting.<br> | ||
+ | '''[ON/OFF/Next]'''<br> | ||
+ | * The final meas. block field shows [''Reg. Position'' | ''Learned'' | ''0.0'' | ''N/A''] again. | ||
+ | The adjustment should now be learned.<br> | ||
+ | '''[Done, Go Back]'''<br> | ||
+ | Don't forget to check/clear fault codes afterwards.<br> | ||
+ | '''[Close Controller, Go Back - 06]'''<br> |
Revision as of 12:23, 21 August 2015
General Information
This page applies to vehicles with factory installed Xenon headlights that do NOT use a diagnostic capable 55-Headlight Range control module. If the vehicle in question has a diagnostic capable 55-Headlight Range control module please use the applicable Ross-Tech Wiki Diagnostic Procedure page for that system.
- Registered VCDS users encountering difficulty determining which type of factory installed Xenon headlight system is installed can:
- Join and post the complete VCDS Auto-Scan in the Car Repair Support section of our forum.
- Send the complete VCDS Auto-Scan directly via email.
- Registered VCDS users encountering difficulty Retrofitting a Xenon headlight system need to join and post in the Retrofits section of our forum. Post the Auto-Scan prior to the retrofit in addition to the Auto-Scan after the replacement parts were installed when assistance is needed.
As of VCDS Release 15.7.0 it is possible to perform Basic Settings in address 09-Cent. Elect. This procedure has received limited feedback to date so Paul's New Xenon Range Adjustment Procedure - HOW TO thread may be helpful.
Basic Setting
Headlight Adjustment
Prerequisites:
- Vehicle on Level ground.
- Headlights, suspension leveling components and similar fully assembled and in proper working order.
- Address 09-Cent. Elect (BCM1) fault free with the exception of 01539, 02658, and 02659.
- Headlight switch ON (not Automatic mode):
[Select]
[09 - Cent. Elect.]
[Basic Settings - 04]
Group 011
[Go!]
- The meas. block field shows [Reg. Position | Learned | 0.0 | N/A]
Activate the Basic Setting.
[ON/OFF/Next]
- The meas. block field now shows [Adjust | Headlights | not available | N/A]
- Adjust the headlights (if needed) using their manual adjusting screws as referenced against a suitable aiming target.
Deactivate the Basic Setting.
[ON/OFF/Next]
- The final meas. block field shows [Reg. Position | Learned | 0.0 | N/A] again.
The adjustment should now be learned.
[Done, Go Back]
Don't forget to check/clear fault codes afterwards.
[Close Controller, Go Back - 06]